Hooks used by git
=================

Hooks are little scripts you can place in `$GIT_DIR/hooks`
directory to trigger action at certain points.  When
`git-init` is run, a handful example hooks are copied in the
`hooks` directory of the new repository, but by default they are
all disabled.  To enable a hook, make it executable with `chmod +x`.

This document describes the currently defined hooks.

applypatch-msg
--------------

This hook is invoked by `git-applypatch` script, which is
typically invoked by `git-applymbox`.  It takes a single
parameter, the name of the file that holds the proposed commit
log message.  Exiting with non-zero status causes
`git-applypatch` to abort before applying the patch.

The hook is allowed to edit the message file in place, and can
be used to normalize the message into some project standard
format (if the project has one). It can also be used to refuse
the commit after inspecting the message file.

The default 'applypatch-msg' hook, when enabled, runs the
'commit-msg' hook, if the latter is enabled.

pre-applypatch
--------------

This hook is invoked by `git-applypatch` script, which is
typically invoked by `git-applymbox`.  It takes no parameter,
and is invoked after the patch is applied, but before a commit
is made.  Exiting with non-zero status causes the working tree
after application of the patch not committed.

It can be used to inspect the current working tree and refuse to
make a commit if it does not pass certain test.

The default 'pre-applypatch' hook, when enabled, runs the
'pre-commit' hook, if the latter is enabled.

post-applypatch
---------------

This hook is invoked by `git-applypatch` script, which is
typically invoked by `git-applymbox`.  It takes no parameter,
and is invoked after the patch is applied and a commit is made.

This hook is meant primarily for notification, and cannot affect
the outcome of `git-applypatch`.

pre-commit
----------

This hook is invoked by `git-commit`, and can be bypassed
with `\--no-verify` option.  It takes no parameter, and is
invoked before obtaining the proposed commit log message and
making a commit.  Exiting with non-zero status from this script
causes the `git-commit` to abort.

The default 'pre-commit' hook, when enabled, catches introduction
of lines with trailing whitespaces and aborts the commit when
such a line is found.

commit-msg
----------

This hook is invoked by `git-commit`, and can be bypassed
with `\--no-verify` option.  It takes a single parameter, the
name of the file that holds the proposed commit log message.
Exiting with non-zero status causes the `git-commit` to
abort.

The hook is allowed to edit the message file in place, and can
be used to normalize the message into some project standard
format (if the project has one). It can also be used to refuse
the commit after inspecting the message file.

The default 'commit-msg' hook, when enabled, detects duplicate
"Signed-off-by" lines, and aborts the commit if one is found.

post-commit
-----------

This hook is invoked by `git-commit`.  It takes no
parameter, and is invoked after a commit is made.

This hook is meant primarily for notification, and cannot affect
the outcome of `git-commit`.

update
------

This hook is invoked by `git-receive-pack` on the remote repository,
which happens when a `git push` is done on a local repository.
Just before updating the ref on the remote repository, the update hook
is invoked.  Its exit status determines the success or failure of
the ref update.

The hook executes once for each ref to be updated, and takes
three parameters:

 - the name of the ref being updated,
 - the old object name stored in the ref,
 - and the new objectname to be stored in the ref.

A zero exit from the update hook allows the ref to be updated.
Exiting with a non-zero status prevents `git-receive-pack`
from updating the ref.

This hook can be used to prevent 'forced' update on certain refs by
making sure that the object name is a commit object that is a
descendant of the commit object named by the old object name.
That is, to enforce a "fast forward only" policy.

It could also be used to log the old..new status.  However, it
does not know the entire set of branches, so it would end up
firing one e-mail per ref when used naively, though.

Another use suggested on the mailing list is to use this hook to
implement access control which is finer grained than the one
based on filesystem group.

The standard output of this hook is sent to `stderr`, so if you
want to report something to the `git-send-pack` on the other end,
you can simply `echo` your messages.

The default 'update' hook, when enabled, demonstrates how to
send out a notification e-mail.

post-update
-----------

This hook is invoked by `git-receive-pack` on the remote repository,
which happens when a `git push` is done on a local repository.
It executes on the remote repository once after all the refs have
been updated.

It takes a variable number of parameters, each of which is the
name of ref that was actually updated.

This hook is meant primarily for notification, and cannot affect
the outcome of `git-receive-pack`.

The 'post-update' hook can tell what are the heads that were pushed,
but it does not know what their original and updated values are,
so it is a poor place to do log old..new.

When enabled, the default 'post-update' hook runs
`git-update-server-info` to keep the information used by dumb
transports (e.g., HTTP) up-to-date.  If you are publishing
a git repository that is accessible via HTTP, you should
probably enable this hook.

The standard output of this hook is sent to `/dev/null`; if you
want to report something to the `git-send-pack` on the other end,
you can redirect your output to your `stderr`.