blob: de3862c15fccad6d8e306f09ce5cea029d5b5e98 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0-only
menu "Remoteproc drivers"
config REMOTEPROC
bool "Support for Remote Processor subsystem"
depends on HAS_DMA
select CRC32
select FW_LOADER
select VIRTIO
select WANT_DEV_COREDUMP
help
Support for remote processors (such as DSP coprocessors). These
are mainly used on embedded systems.
if REMOTEPROC
config IMX_REMOTEPROC
tristate "IMX6/7 remoteproc support"
depends on ARCH_MXC
help
Say y here to support iMX's remote processors (Cortex M4
on iMX7D) via the remote processor framework.
It's safe to say N here.
config MTK_SCP
tristate "Mediatek SCP support"
depends on ARCH_MEDIATEK
select RPMSG_MTK_SCP
help
Say y here to support Mediatek's System Companion Processor (SCP) via
the remote processor framework.
It's safe to say N here.
config OMAP_REMOTEPROC
tristate "OMAP remoteproc support"
depends on ARCH_OMAP4 || SOC_OMAP5
depends on OMAP_IOMMU
select MAILBOX
select OMAP2PLUS_MBOX
help
Say y here to support OMAP's remote processors (dual M3
and DSP on OMAP4) via the remote processor framework.
Currently only supported on OMAP4.
Usually you want to say Y here, in order to enable multimedia
use-cases to run on your platform (multimedia codecs are
offloaded to remote DSP processors using this framework).
It's safe to say N here if you're not interested in multimedia
offloading or just want a bare minimum kernel.
config WKUP_M3_RPROC
tristate "AMx3xx Wakeup M3 remoteproc support"
depends on SOC_AM33XX || SOC_AM43XX
help
Say y here to support Wakeup M3 remote processor on TI AM33xx
and AM43xx family of SoCs.
Required for Suspend-to-RAM on AM33xx and AM43xx SoCs. Also needed
for deep CPUIdle states on AM33xx SoCs. Allows for loading of the
firmware onto these remote processors.
If unsure say N.
config DA8XX_REMOTEPROC
tristate "DA8xx/OMAP-L13x remoteproc support"
depends on ARCH_DAVINCI_DA8XX
depends on DMA_CMA
help
Say y here to support DA8xx/OMAP-L13x remote processors via the
remote processor framework.
You want to say y here in order to enable AMP
use-cases to run on your platform (multimedia codecs are
offloaded to remote DSP processors using this framework).
This module controls the name of the firmware file that gets
loaded on the DSP. This file must reside in the /lib/firmware
directory. It can be specified via the module parameter
da8xx_fw_name=<filename>, and if not specified will default to
"rproc-dsp-fw".
It's safe to say n here if you're not interested in multimedia
offloading.
config KEYSTONE_REMOTEPROC
tristate "Keystone Remoteproc support"
depends on ARCH_KEYSTONE
help
Say Y here here to support Keystone remote processors (DSP)
via the remote processor framework.
It's safe to say N here if you're not interested in the Keystone
DSPs or just want to use a bare minimum kernel.
config QCOM_RPROC_COMMON
tristate
config QCOM_Q6V5_COMMON
tristate
depends on ARCH_QCOM
depends on QCOM_SMEM
config QCOM_Q6V5_ADSP
tristate "Qualcomm Technology Inc ADSP Peripheral Image Loader"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
depends on QCOM_SYSMON || QCOM_SYSMON=n
select MFD_SYSCON
select QCOM_MDT_LOADER
select QCOM_Q6V5_COMMON
select QCOM_RPROC_COMMON
help
Say y here to support the Peripheral Image Loader
for the Qualcomm Technology Inc. ADSP remote processors.
config QCOM_Q6V5_MSS
tristate "Qualcomm Hexagon V5 self-authenticating modem subsystem support"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
depends on QCOM_SYSMON || QCOM_SYSMON=n
select MFD_SYSCON
select QCOM_MDT_LOADER
select QCOM_Q6V5_COMMON
select QCOM_RPROC_COMMON
select QCOM_SCM
help
Say y here to support the Qualcomm self-authenticating modem
subsystem based on Hexagon V5.
config QCOM_Q6V5_PAS
tristate "Qualcomm Hexagon v5 Peripheral Authentication Service support"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
depends on QCOM_SYSMON || QCOM_SYSMON=n
select MFD_SYSCON
select QCOM_MDT_LOADER
select QCOM_Q6V5_COMMON
select QCOM_RPROC_COMMON
select QCOM_SCM
help
Say y here to support the TrustZone based Peripherial Image Loader
for the Qualcomm Hexagon v5 based remote processors. This is commonly
used to control subsystems such as ADSP, Compute and Sensor.
config QCOM_Q6V5_WCSS
tristate "Qualcomm Hexagon based WCSS Peripheral Image Loader"
depends on OF && ARCH_QCOM
depends on QCOM_SMEM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
depends on QCOM_SYSMON || QCOM_SYSMON=n
select MFD_SYSCON
select QCOM_MDT_LOADER
select QCOM_Q6V5_COMMON
select QCOM_RPROC_COMMON
select QCOM_SCM
help
Say y here to support the Qualcomm Peripheral Image Loader for the
Hexagon V5 based WCSS remote processors.
config QCOM_SYSMON
tristate "Qualcomm sysmon driver"
depends on RPMSG
depends on ARCH_QCOM
depends on NET
select QCOM_QMI_HELPERS
help
The sysmon driver implements a sysmon QMI client and a handler for
the sys_mon SMD and GLINK channel, which are used for graceful
shutdown, retrieving failure information and propagating information
about other subsystems being shut down.
Say y here if your system runs firmware on any other subsystems, e.g.
modem or DSP.
config QCOM_WCNSS_PIL
tristate "Qualcomm WCNSS Peripheral Image Loader"
depends on OF && ARCH_QCOM
depends on RPMSG_QCOM_SMD || (COMPILE_TEST && RPMSG_QCOM_SMD=n)
depends on RPMSG_QCOM_GLINK_SMEM || RPMSG_QCOM_GLINK_SMEM=n
depends on QCOM_SMEM
depends on QCOM_SYSMON || QCOM_SYSMON=n
select QCOM_MDT_LOADER
select QCOM_RPROC_COMMON
select QCOM_SCM
help
Say y here to support the Peripheral Image Loader for the Qualcomm
Wireless Connectivity Subsystem.
config ST_REMOTEPROC
tristate "ST remoteproc support"
depends on ARCH_STI
select MAILBOX
select STI_MBOX
help
Say y here to support ST's adjunct processors via the remote
processor framework.
This can be either built-in or a loadable module.
config ST_SLIM_REMOTEPROC
tristate
config STM32_RPROC
tristate "STM32 remoteproc support"
depends on ARCH_STM32
depends on REMOTEPROC
select MAILBOX
help
Say y here to support STM32 MCU processors via the
remote processor framework.
You want to say y here in order to enable AMP
use-cases to run on your platform (dedicated firmware could be
offloaded to remote MCU processors using this framework).
This can be either built-in or a loadable module.
endif # REMOTEPROC
endmenu