drivers/ata/pata_artop.c - linux/torvalds/linux - Git at Google

 // SPDX-License-Identifier: GPL-2.0-only
 /*
  *    pata_artop.c - ARTOP ATA controller driver
  *
  *	(C) 2006 Red Hat
  *	(C) 2007,2011 Bartlomiej Zolnierkiewicz
  *
  *    Based in part on drivers/ide/pci/aec62xx.c
  *	Copyright (C) 1999-2002	Andre Hedrick <andre@linux-ide.org>
  *	865/865R fixes for Macintosh card version from a patch to the old
  *		driver by Thibaut VARENE <varenet@parisc-linux.org>
  *	When setting the PCI latency we must set 0x80 or higher for burst
  *		performance Alessandro Zummo <alessandro.zummo@towertech.it>
  *
  *	TODO
  *	Investigate no_dsc on 850R
  *	Clock detect
  */

 #include <linux/kernel.h>
 #include <linux/module.h>
 #include <linux/pci.h>
 #include <linux/blkdev.h>
 #include <linux/delay.h>
 #include <linux/device.h>
 #include <scsi/scsi_host.h>
 #include <linux/libata.h>
 #include <linux/ata.h>

 #define DRV_NAME	"pata_artop"
 #define DRV_VERSION	"0.4.6"

 /*
  *	The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
  *	get PCI bus speed functionality we leave this as 0. Its a variable
  *	for when we get the functionality and also for folks wanting to
  *	test stuff.
  */

 static int clock = 0;

 /**
  *	artop62x0_pre_reset	-	probe begin
  *	@link: link
  *	@deadline: deadline jiffies for the operation
  *
  *	Nothing complicated needed here.
  */

 static int artop62x0_pre_reset(struct ata_link *link, unsigned long deadline)
 {
 	static const struct pci_bits artop_enable_bits[] = {
 		{ 0x4AU, 1U, 0x02UL, 0x02UL },	/* port 0 */
 		{ 0x4AU, 1U, 0x04UL, 0x04UL },	/* port 1 */
 	};

 	struct ata_port *ap = link->ap;
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

 	/* Odd numbered device ids are the units with enable bits. */
 	if ((pdev->device & 1) &&
 	    !pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
 		return -ENOENT;

 	return ata_sff_prereset(link, deadline);
 }

 /**
  *	artop6260_cable_detect	-	identify cable type
  *	@ap: Port
  *
  *	Identify the cable type for the ARTOP interface in question
  */

 static int artop6260_cable_detect(struct ata_port *ap)
 {
 	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
 	u8 tmp;
 	pci_read_config_byte(pdev, 0x49, &tmp);
 	if (tmp & (1 << ap->port_no))
 		return ATA_CBL_PATA40;
 	return ATA_CBL_PATA80;
 }

 /**
  *	artop6210_load_piomode - Load a set of PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device
  *	@pio: PIO mode
  *
  *	Set PIO mode for device, in host controller PCI config space. This
  *	is used both to set PIO timings in PIO mode and also to set the
  *	matching PIO clocking for UDMA, as well as the MWDMA timings.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6210_load_piomode(struct ata_port *ap, struct ata_device *adev, unsigned int pio)
 {
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	int dn = adev->devno + 2 * ap->port_no;
 	static const u16 timing[2][5] = {
 		{ 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
 		{ 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }

 	};
 	/* Load the PIO timing active/recovery bits */
 	pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
 }

 /**
  *	artop6210_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring
  *
  *	Set PIO mode for device, in host controller PCI config space. For
  *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
  *	the event UDMA is used the later call to set_dmamode will set the
  *	bits as required.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6210_set_piomode(struct ata_port *ap, struct ata_device *adev)
 {
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	int dn = adev->devno + 2 * ap->port_no;
 	u8 ultra;

 	artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);

 	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
 	pci_read_config_byte(pdev, 0x54, &ultra);
 	ultra &= ~(3 << (2 * dn));
 	pci_write_config_byte(pdev, 0x54, ultra);
 }

 /**
  *	artop6260_load_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring
  *	@pio: PIO mode
  *
  *	Set PIO mode for device, in host controller PCI config space. The
  *	ARTOP6260 and relatives store the timing data differently.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6260_load_piomode (struct ata_port *ap, struct ata_device *adev, unsigned int pio)
 {
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	int dn = adev->devno + 2 * ap->port_no;
 	static const u8 timing[2][5] = {
 		{ 0x00, 0x0A, 0x08, 0x33, 0x31 },
 		{ 0x70, 0x7A, 0x78, 0x43, 0x41 }

 	};
 	/* Load the PIO timing active/recovery bits */
 	pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
 }

 /**
  *	artop6260_set_piomode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring
  *
  *	Set PIO mode for device, in host controller PCI config space. For
  *	ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
  *	the event UDMA is used the later call to set_dmamode will set the
  *	bits as required.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6260_set_piomode(struct ata_port *ap, struct ata_device *adev)
 {
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	u8 ultra;

 	artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);

 	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
 	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
 	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
 	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
 }

 /**
  *	artop6210_set_dmamode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device whose timings we are configuring
  *
  *	Set DMA mode for device, in host controller PCI config space.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 {
 	unsigned int pio;
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	int dn = adev->devno + 2 * ap->port_no;
 	u8 ultra;

 	if (adev->dma_mode == XFER_MW_DMA_0)
 		pio = 1;
 	else
 		pio = 4;

 	/* Load the PIO timing active/recovery bits */
 	artop6210_load_piomode(ap, adev, pio);

 	pci_read_config_byte(pdev, 0x54, &ultra);
 	ultra &= ~(3 << (2 * dn));

 	/* Add ultra DMA bits if in UDMA mode */
 	if (adev->dma_mode >= XFER_UDMA_0) {
 		u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
 		if (mode == 0)
 			mode = 1;
 		ultra |= (mode << (2 * dn));
 	}
 	pci_write_config_byte(pdev, 0x54, ultra);
 }

 /**
  *	artop6260_set_dmamode - Initialize host controller PATA PIO timings
  *	@ap: Port whose timings we are configuring
  *	@adev: Device we are configuring
  *
  *	Set DMA mode for device, in host controller PCI config space. The
  *	ARTOP6260 and relatives store the timing data differently.
  *
  *	LOCKING:
  *	None (inherited from caller).
  */

 static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 {
 	unsigned int pio;
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	u8 ultra;

 	if (adev->dma_mode == XFER_MW_DMA_0)
 		pio = 1;
 	else
 		pio = 4;

 	/* Load the PIO timing active/recovery bits */
 	artop6260_load_piomode(ap, adev, pio);

 	/* Add ultra DMA bits if in UDMA mode */
 	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
 	ultra &= ~(7 << (4  * adev->devno));	/* One nibble per drive */
 	if (adev->dma_mode >= XFER_UDMA_0) {
 		u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
 		if (mode == 0)
 			mode = 1;
 		ultra |= (mode << (4 * adev->devno));
 	}
 	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
 }

 /**
  *	artop_6210_qc_defer	-	implement serialization
  *	@qc: command
  *
  *	Issue commands per host on this chip.
  */

 static int artop6210_qc_defer(struct ata_queued_cmd *qc)
 {
 	struct ata_host *host = qc->ap->host;
 	struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
 	int rc;

 	/* First apply the usual rules */
 	rc = ata_std_qc_defer(qc);
 	if (rc != 0)
 		return rc;

 	/* Now apply serialization rules. Only allow a command if the
 	   other channel state machine is idle */
 	if (alt && alt->qc_active)
 		return	ATA_DEFER_PORT;
 	return 0;
 }

 static struct scsi_host_template artop_sht = {
 	ATA_BMDMA_SHT(DRV_NAME),
 };

 static struct ata_port_operations artop6210_ops = {
 	.inherits		= &ata_bmdma_port_ops,
 	.cable_detect		= ata_cable_40wire,
 	.set_piomode		= artop6210_set_piomode,
 	.set_dmamode		= artop6210_set_dmamode,
 	.prereset		= artop62x0_pre_reset,
 	.qc_defer		= artop6210_qc_defer,
 };

 static struct ata_port_operations artop6260_ops = {
 	.inherits		= &ata_bmdma_port_ops,
 	.cable_detect		= artop6260_cable_detect,
 	.set_piomode		= artop6260_set_piomode,
 	.set_dmamode		= artop6260_set_dmamode,
 	.prereset		= artop62x0_pre_reset,
 };

 static void atp8xx_fixup(struct pci_dev *pdev)
 {
 	if (pdev->device == 0x0005)
 		/* BIOS may have left us in UDMA, clear it before libata probe */
 		pci_write_config_byte(pdev, 0x54, 0);
 	else if (pdev->device == 0x0008 || pdev->device == 0x0009) {
 		u8 reg;

 		/* Mac systems come up with some registers not set as we
 		   will need them */

 		/* Clear reset & test bits */
 		pci_read_config_byte(pdev, 0x49, &reg);
 		pci_write_config_byte(pdev, 0x49, reg & ~0x30);

 		/* PCI latency must be > 0x80 for burst mode, tweak it
 		 * if required.
 		 */
 		pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
 		if (reg <= 0x80)
 			pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);

 		/* Enable IRQ output and burst mode */
 		pci_read_config_byte(pdev, 0x4a, &reg);
 		pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) | 0x80);
 	}
 }

 /**
  *	artop_init_one - Register ARTOP ATA PCI device with kernel services
  *	@pdev: PCI device to register
  *	@ent: Entry in artop_pci_tbl matching with @pdev
  *
  *	Called from kernel PCI layer.
  *
  *	LOCKING:
  *	Inherited from PCI layer (may sleep).
  *
  *	RETURNS:
  *	Zero on success, or -ERRNO value.
  */

 static int artop_init_one (struct pci_dev *pdev, const struct pci_device_id *id)
 {
 	static const struct ata_port_info info_6210 = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask 	= ATA_UDMA2,
 		.port_ops	= &artop6210_ops,
 	};
 	static const struct ata_port_info info_626x = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask 	= ATA_UDMA4,
 		.port_ops	= &artop6260_ops,
 	};
 	static const struct ata_port_info info_628x = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask 	= ATA_UDMA5,
 		.port_ops	= &artop6260_ops,
 	};
 	static const struct ata_port_info info_628x_fast = {
 		.flags		= ATA_FLAG_SLAVE_POSS,
 		.pio_mask	= ATA_PIO4,
 		.mwdma_mask	= ATA_MWDMA2,
 		.udma_mask 	= ATA_UDMA6,
 		.port_ops	= &artop6260_ops,
 	};
 	const struct ata_port_info *ppi[] = { NULL, NULL };
 	int rc;

 	ata_print_version_once(&pdev->dev, DRV_VERSION);

 	rc = pcim_enable_device(pdev);
 	if (rc)
 		return rc;

 	if (id->driver_data == 0)	/* 6210 variant */
 		ppi[0] = &info_6210;
 	else if (id->driver_data == 1)	/* 6260 */
 		ppi[0] = &info_626x;
 	else if (id->driver_data == 2)	{ /* 6280 or 6280 + fast */
 		unsigned long io = pci_resource_start(pdev, 4);

 		ppi[0] = &info_628x;
 		if (inb(io) & 0x10)
 			ppi[0] = &info_628x_fast;
 	}

 	BUG_ON(ppi[0] == NULL);

 	atp8xx_fixup(pdev);

 	return ata_pci_bmdma_init_one(pdev, ppi, &artop_sht, NULL, 0);
 }

 static const struct pci_device_id artop_pci_tbl[] = {
 	{ PCI_VDEVICE(ARTOP, 0x0005), 0 },
 	{ PCI_VDEVICE(ARTOP, 0x0006), 1 },
 	{ PCI_VDEVICE(ARTOP, 0x0007), 1 },
 	{ PCI_VDEVICE(ARTOP, 0x0008), 2 },
 	{ PCI_VDEVICE(ARTOP, 0x0009), 2 },

 	{ }	/* terminate list */
 };

 #ifdef CONFIG_PM_SLEEP
 static int atp8xx_reinit_one(struct pci_dev *pdev)
 {
 	struct ata_host *host = pci_get_drvdata(pdev);
 	int rc;

 	rc = ata_pci_device_do_resume(pdev);
 	if (rc)
 		return rc;

 	atp8xx_fixup(pdev);

 	ata_host_resume(host);
 	return 0;
 }
 #endif

 static struct pci_driver artop_pci_driver = {
 	.name			= DRV_NAME,
 	.id_table		= artop_pci_tbl,
 	.probe			= artop_init_one,
 	.remove			= ata_pci_remove_one,
 #ifdef CONFIG_PM_SLEEP
 	.suspend		= ata_pci_device_suspend,
 	.resume			= atp8xx_reinit_one,
 #endif
 };

 module_pci_driver(artop_pci_driver);

 MODULE_AUTHOR("Alan Cox, Bartlomiej Zolnierkiewicz");
 MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
 MODULE_LICENSE("GPL");
 MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
 MODULE_VERSION(DRV_VERSION);
	// SPDX-License-Identifier: GPL-2.0-only
	/*
	* pata_artop.c - ARTOP ATA controller driver
	*
	* (C) 2006 Red Hat
	* (C) 2007,2011 Bartlomiej Zolnierkiewicz
	*
	* Based in part on drivers/ide/pci/aec62xx.c
	* Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org>
	* 865/865R fixes for Macintosh card version from a patch to the old
	* driver by Thibaut VARENE <varenet@parisc-linux.org>
	* When setting the PCI latency we must set 0x80 or higher for burst
	* performance Alessandro Zummo <alessandro.zummo@towertech.it>
	*
	* TODO
	* Investigate no_dsc on 850R
	* Clock detect
	*/

	#include <linux/kernel.h>
	#include <linux/module.h>
	#include <linux/pci.h>
	#include <linux/blkdev.h>
	#include <linux/delay.h>
	#include <linux/device.h>
	#include <scsi/scsi_host.h>
	#include <linux/libata.h>
	#include <linux/ata.h>

	#define DRV_NAME "pata_artop"
	#define DRV_VERSION "0.4.6"

	/*
	* The ARTOP has 33 Mhz and "over clocked" timing tables. Until we
	* get PCI bus speed functionality we leave this as 0. Its a variable
	* for when we get the functionality and also for folks wanting to
	* test stuff.
	*/

	static int clock = 0;

	/**
	* artop62x0_pre_reset - probe begin
	* @link: link
	* @deadline: deadline jiffies for the operation
	*
	* Nothing complicated needed here.
	*/

	static int artop62x0_pre_reset(struct ata_link *link, unsigned long deadline)
	{
	static const struct pci_bits artop_enable_bits[] = {
	{ 0x4AU, 1U, 0x02UL, 0x02UL }, /* port 0 */
	{ 0x4AU, 1U, 0x04UL, 0x04UL }, /* port 1 */
	};

	struct ata_port *ap = link->ap;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);

	/* Odd numbered device ids are the units with enable bits. */
	if ((pdev->device & 1) &&
	!pci_test_config_bits(pdev, &artop_enable_bits[ap->port_no]))
	return -ENOENT;

	return ata_sff_prereset(link, deadline);
	}

	/**
	* artop6260_cable_detect - identify cable type
	* @ap: Port
	*
	* Identify the cable type for the ARTOP interface in question
	*/

	static int artop6260_cable_detect(struct ata_port *ap)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u8 tmp;
	pci_read_config_byte(pdev, 0x49, &tmp);
	if (tmp & (1 << ap->port_no))
	return ATA_CBL_PATA40;
	return ATA_CBL_PATA80;
	}

	/**
	* artop6210_load_piomode - Load a set of PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device
	* @pio: PIO mode
	*
	* Set PIO mode for device, in host controller PCI config space. This
	* is used both to set PIO timings in PIO mode and also to set the
	* matching PIO clocking for UDMA, as well as the MWDMA timings.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6210_load_piomode(struct ata_port ap, struct ata_device adev, unsigned int pio)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int dn = adev->devno + 2 * ap->port_no;
	static const u16 timing[2][5] = {
	{ 0x0000, 0x000A, 0x0008, 0x0303, 0x0301 },
	{ 0x0700, 0x070A, 0x0708, 0x0403, 0x0401 }

	};
	/* Load the PIO timing active/recovery bits */
	pci_write_config_word(pdev, 0x40 + 2 * dn, timing[clock][pio]);
	}

	/**
	* artop6210_set_piomode - Initialize host controller PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device we are configuring
	*
	* Set PIO mode for device, in host controller PCI config space. For
	* ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
	* the event UDMA is used the later call to set_dmamode will set the
	* bits as required.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6210_set_piomode(struct ata_port ap, struct ata_device adev)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int dn = adev->devno + 2 * ap->port_no;
	u8 ultra;

	artop6210_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);

	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
	pci_read_config_byte(pdev, 0x54, &ultra);
	ultra &= ~(3 << (2 * dn));
	pci_write_config_byte(pdev, 0x54, ultra);
	}

	/**
	* artop6260_load_piomode - Initialize host controller PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device we are configuring
	* @pio: PIO mode
	*
	* Set PIO mode for device, in host controller PCI config space. The
	* ARTOP6260 and relatives store the timing data differently.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6260_load_piomode (struct ata_port ap, struct ata_device adev, unsigned int pio)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int dn = adev->devno + 2 * ap->port_no;
	static const u8 timing[2][5] = {
	{ 0x00, 0x0A, 0x08, 0x33, 0x31 },
	{ 0x70, 0x7A, 0x78, 0x43, 0x41 }

	};
	/* Load the PIO timing active/recovery bits */
	pci_write_config_byte(pdev, 0x40 + dn, timing[clock][pio]);
	}

	/**
	* artop6260_set_piomode - Initialize host controller PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device we are configuring
	*
	* Set PIO mode for device, in host controller PCI config space. For
	* ARTOP we must also clear the UDMA bits if we are not doing UDMA. In
	* the event UDMA is used the later call to set_dmamode will set the
	* bits as required.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6260_set_piomode(struct ata_port ap, struct ata_device adev)
	{
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u8 ultra;

	artop6260_load_piomode(ap, adev, adev->pio_mode - XFER_PIO_0);

	/* Clear the UDMA mode bits (set_dmamode will redo this if needed) */
	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
	ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
	}

	/**
	* artop6210_set_dmamode - Initialize host controller PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device whose timings we are configuring
	*
	* Set DMA mode for device, in host controller PCI config space.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6210_set_dmamode (struct ata_port ap, struct ata_device adev)
	{
	unsigned int pio;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	int dn = adev->devno + 2 * ap->port_no;
	u8 ultra;

	if (adev->dma_mode == XFER_MW_DMA_0)
	pio = 1;
	else
	pio = 4;

	/* Load the PIO timing active/recovery bits */
	artop6210_load_piomode(ap, adev, pio);

	pci_read_config_byte(pdev, 0x54, &ultra);
	ultra &= ~(3 << (2 * dn));

	/* Add ultra DMA bits if in UDMA mode */
	if (adev->dma_mode >= XFER_UDMA_0) {
	u8 mode = (adev->dma_mode - XFER_UDMA_0) + 1 - clock;
	if (mode == 0)
	mode = 1;
	ultra \|= (mode << (2 * dn));
	}
	pci_write_config_byte(pdev, 0x54, ultra);
	}

	/**
	* artop6260_set_dmamode - Initialize host controller PATA PIO timings
	* @ap: Port whose timings we are configuring
	* @adev: Device we are configuring
	*
	* Set DMA mode for device, in host controller PCI config space. The
	* ARTOP6260 and relatives store the timing data differently.
	*
	* LOCKING:
	* None (inherited from caller).
	*/

	static void artop6260_set_dmamode (struct ata_port ap, struct ata_device adev)
	{
	unsigned int pio;
	struct pci_dev *pdev = to_pci_dev(ap->host->dev);
	u8 ultra;

	if (adev->dma_mode == XFER_MW_DMA_0)
	pio = 1;
	else
	pio = 4;

	/* Load the PIO timing active/recovery bits */
	artop6260_load_piomode(ap, adev, pio);

	/* Add ultra DMA bits if in UDMA mode */
	pci_read_config_byte(pdev, 0x44 + ap->port_no, &ultra);
	ultra &= ~(7 << (4 * adev->devno)); /* One nibble per drive */
	if (adev->dma_mode >= XFER_UDMA_0) {
	u8 mode = adev->dma_mode - XFER_UDMA_0 + 1 - clock;
	if (mode == 0)
	mode = 1;
	ultra \|= (mode << (4 * adev->devno));
	}
	pci_write_config_byte(pdev, 0x44 + ap->port_no, ultra);
	}

	/**
	* artop_6210_qc_defer - implement serialization
	* @qc: command
	*
	* Issue commands per host on this chip.
	*/

	static int artop6210_qc_defer(struct ata_queued_cmd *qc)
	{
	struct ata_host *host = qc->ap->host;
	struct ata_port *alt = host->ports[1 ^ qc->ap->port_no];
	int rc;

	/* First apply the usual rules */
	rc = ata_std_qc_defer(qc);
	if (rc != 0)
	return rc;

	/* Now apply serialization rules. Only allow a command if the
	other channel state machine is idle */
	if (alt && alt->qc_active)
	return ATA_DEFER_PORT;
	return 0;
	}

	static struct scsi_host_template artop_sht = {
	ATA_BMDMA_SHT(DRV_NAME),
	};

	static struct ata_port_operations artop6210_ops = {
	.inherits = &ata_bmdma_port_ops,
	.cable_detect = ata_cable_40wire,
	.set_piomode = artop6210_set_piomode,
	.set_dmamode = artop6210_set_dmamode,
	.prereset = artop62x0_pre_reset,
	.qc_defer = artop6210_qc_defer,
	};

	static struct ata_port_operations artop6260_ops = {
	.inherits = &ata_bmdma_port_ops,
	.cable_detect = artop6260_cable_detect,
	.set_piomode = artop6260_set_piomode,
	.set_dmamode = artop6260_set_dmamode,
	.prereset = artop62x0_pre_reset,
	};

	static void atp8xx_fixup(struct pci_dev *pdev)
	{
	if (pdev->device == 0x0005)
	/* BIOS may have left us in UDMA, clear it before libata probe */
	pci_write_config_byte(pdev, 0x54, 0);
	else if (pdev->device == 0x0008 \|\| pdev->device == 0x0009) {
	u8 reg;

	/* Mac systems come up with some registers not set as we
	will need them */

	/* Clear reset & test bits */
	pci_read_config_byte(pdev, 0x49, &reg);
	pci_write_config_byte(pdev, 0x49, reg & ~0x30);

	/* PCI latency must be > 0x80 for burst mode, tweak it
	* if required.
	*/
	pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &reg);
	if (reg <= 0x80)
	pci_write_config_byte(pdev, PCI_LATENCY_TIMER, 0x90);

	/* Enable IRQ output and burst mode */
	pci_read_config_byte(pdev, 0x4a, &reg);
	pci_write_config_byte(pdev, 0x4a, (reg & ~0x01) \| 0x80);
	}
	}

	/**
	* artop_init_one - Register ARTOP ATA PCI device with kernel services
	* @pdev: PCI device to register
	* @ent: Entry in artop_pci_tbl matching with @pdev
	*
	* Called from kernel PCI layer.
	*
	* LOCKING:
	* Inherited from PCI layer (may sleep).
	*
	* RETURNS:
	* Zero on success, or -ERRNO value.
	*/

	static int artop_init_one (struct pci_dev pdev, const struct pci_device_id id)
	{
	static const struct ata_port_info info_6210 = {
	.flags = ATA_FLAG_SLAVE_POSS,
	.pio_mask = ATA_PIO4,
	.mwdma_mask = ATA_MWDMA2,
	.udma_mask = ATA_UDMA2,
	.port_ops = &artop6210_ops,
	};
	static const struct ata_port_info info_626x = {
	.flags = ATA_FLAG_SLAVE_POSS,
	.pio_mask = ATA_PIO4,
	.mwdma_mask = ATA_MWDMA2,
	.udma_mask = ATA_UDMA4,
	.port_ops = &artop6260_ops,
	};
	static const struct ata_port_info info_628x = {
	.flags = ATA_FLAG_SLAVE_POSS,
	.pio_mask = ATA_PIO4,
	.mwdma_mask = ATA_MWDMA2,
	.udma_mask = ATA_UDMA5,
	.port_ops = &artop6260_ops,
	};
	static const struct ata_port_info info_628x_fast = {
	.flags = ATA_FLAG_SLAVE_POSS,
	.pio_mask = ATA_PIO4,
	.mwdma_mask = ATA_MWDMA2,
	.udma_mask = ATA_UDMA6,
	.port_ops = &artop6260_ops,
	};
	const struct ata_port_info *ppi[] = { NULL, NULL };
	int rc;

	ata_print_version_once(&pdev->dev, DRV_VERSION);

	rc = pcim_enable_device(pdev);
	if (rc)
	return rc;

	if (id->driver_data == 0) /* 6210 variant */
	ppi[0] = &info_6210;
	else if (id->driver_data == 1) /* 6260 */
	ppi[0] = &info_626x;
	else if (id->driver_data == 2) { /* 6280 or 6280 + fast */
	unsigned long io = pci_resource_start(pdev, 4);

	ppi[0] = &info_628x;
	if (inb(io) & 0x10)
	ppi[0] = &info_628x_fast;
	}

	BUG_ON(ppi[0] == NULL);

	atp8xx_fixup(pdev);

	return ata_pci_bmdma_init_one(pdev, ppi, &artop_sht, NULL, 0);
	}

	static const struct pci_device_id artop_pci_tbl[] = {
	{ PCI_VDEVICE(ARTOP, 0x0005), 0 },
	{ PCI_VDEVICE(ARTOP, 0x0006), 1 },
	{ PCI_VDEVICE(ARTOP, 0x0007), 1 },
	{ PCI_VDEVICE(ARTOP, 0x0008), 2 },
	{ PCI_VDEVICE(ARTOP, 0x0009), 2 },

	{ } /* terminate list */
	};

	#ifdef CONFIG_PM_SLEEP
	static int atp8xx_reinit_one(struct pci_dev *pdev)
	{
	struct ata_host *host = pci_get_drvdata(pdev);
	int rc;

	rc = ata_pci_device_do_resume(pdev);
	if (rc)
	return rc;

	atp8xx_fixup(pdev);

	ata_host_resume(host);
	return 0;
	}
	#endif

	static struct pci_driver artop_pci_driver = {
	.name = DRV_NAME,
	.id_table = artop_pci_tbl,
	.probe = artop_init_one,
	.remove = ata_pci_remove_one,
	#ifdef CONFIG_PM_SLEEP
	.suspend = ata_pci_device_suspend,
	.resume = atp8xx_reinit_one,
	#endif
	};

	module_pci_driver(artop_pci_driver);

	MODULE_AUTHOR("Alan Cox, Bartlomiej Zolnierkiewicz");
	MODULE_DESCRIPTION("SCSI low-level driver for ARTOP PATA");
	MODULE_LICENSE("GPL");
	MODULE_DEVICE_TABLE(pci, artop_pci_tbl);
	MODULE_VERSION(DRV_VERSION);