blob: 21876da7c44250c752c28983e894fa2f536352cc [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* at91-dvk_su60_somc.dtsi - Device Tree file for the DVK SOM60 base board
*
* Copyright (C) 2018 Laird,
* 2018 Ben Whitten <ben.whitten@lairdtech.com>
*
*/
/ {
sound {
compatible = "atmel,asoc-wm8904";
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_pck2_as_audio_mck>;
atmel,model = "wm8904 @ DVK-SOM60";
atmel,audio-routing =
"Headphone Jack", "HPOUTL",
"Headphone Jack", "HPOUTR",
"IN2L", "Line In Jack",
"IN2R", "Line In Jack",
"Mic", "MICBIAS",
"IN1L", "Mic";
atmel,ssc-controller = <&ssc0>;
atmel,audio-codec = <&wm8904>;
status = "okay";
};
};
&mmc0 {
status = "okay";
pinctrl-0 = <&pinctrl_mmc0_clk_cmd_dat0 &pinctrl_mmc0_dat1_3 &pinctrl_mmc0_cd>;
slot@0 {
bus-width = <4>;
cd-gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
cd-inverted;
};
};
&spi0 {
status = "okay";
/* spi0.0: 4M Flash Macronix MX25R4035FM1IL0 */
spi-flash@0 {
compatible = "mxicy,mx25u4035", "jedec,spi-nor";
spi-max-frequency = <33000000>;
reg = <0>;
};
};
&ssc0 {
atmel,clk-from-rk-pin;
status = "okay";
};
&i2c0 {
status = "okay";
wm8904: wm8904@1a {
compatible = "wlf,wm8904";
reg = <0x1a>;
clocks = <&pck2>;
clock-names = "mclk";
};
};
&i2c1 {
status = "okay";
eeprom@57 {
compatible = "giantec,gt24c32a", "atmel,24c32";
reg = <0x57>;
pagesize = <32>;
};
};
&usart1 {
status = "okay";
};
&usart2 {
status = "okay";
};
&usart3 {
status = "okay";
};
&uart0 {
status = "okay";
};
&dbgu {
status = "okay";
};
&pit {
status = "okay";
};
&adc0 {
status = "okay";
};
&can1 {
status = "okay";
};
&macb0 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ethernet-phy@7 {
reg = <7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_geth_int>;
interrupt-parent = <&pioB>;
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
txen-skew-ps = <800>;
txc-skew-ps = <3000>;
rxdv-skew-ps = <400>;
rxc-skew-ps = <3000>;
rxd0-skew-ps = <400>;
rxd1-skew-ps = <400>;
rxd2-skew-ps = <400>;
rxd3-skew-ps = <400>;
};
};
&macb1 {
#address-cells = <1>;
#size-cells = <0>;
status = "okay";
ethernet-phy@1 {
reg = <1>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_eth_int>;
interrupt-parent = <&pioC>;
interrupts = <10 IRQ_TYPE_EDGE_FALLING>;
};
};
&usb0 {
status = "okay";
};
&usb1 {
status = "okay";
};
&usb2 {
status = "okay";
};