// SPDX-License-Identifier: GPL-2.0-only
/*
 * Regulator driver for Rockchip RK805/RK808/RK818
 *
 * Copyright (c) 2014, Fuzhou Rockchip Electronics Co., Ltd
 *
 * Author: Chris Zhong <zyw@rock-chips.com>
 * Author: Zhang Qing <zhangqing@rock-chips.com>
 *
 * Copyright (C) 2016 PHYTEC Messtechnik GmbH
 *
 * Author: Wadim Egorov <w.egorov@phytec.de>
 */

#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
#include <linux/module.h>
#include <linux/of_device.h>
#include <linux/of_gpio.h>
#include <linux/mfd/rk808.h>
#include <linux/regulator/driver.h>
#include <linux/regulator/of_regulator.h>
#include <linux/gpio/consumer.h>

/* Field Definitions */
#define RK808_BUCK_VSEL_MASK	0x3f
#define RK808_BUCK4_VSEL_MASK	0xf
#define RK808_LDO_VSEL_MASK	0x1f

#define RK818_BUCK_VSEL_MASK		0x3f
#define RK818_BUCK4_VSEL_MASK		0x1f
#define RK818_LDO_VSEL_MASK		0x1f
#define RK818_LDO3_ON_VSEL_MASK		0xf
#define RK818_BOOST_ON_VSEL_MASK	0xe0

/* Ramp rate definitions for buck1 / buck2 only */
#define RK808_RAMP_RATE_OFFSET		3
#define RK808_RAMP_RATE_MASK		(3 << RK808_RAMP_RATE_OFFSET)
#define RK808_RAMP_RATE_2MV_PER_US	(0 << RK808_RAMP_RATE_OFFSET)
#define RK808_RAMP_RATE_4MV_PER_US	(1 << RK808_RAMP_RATE_OFFSET)
#define RK808_RAMP_RATE_6MV_PER_US	(2 << RK808_RAMP_RATE_OFFSET)
#define RK808_RAMP_RATE_10MV_PER_US	(3 << RK808_RAMP_RATE_OFFSET)

#define RK808_DVS2_POL		BIT(2)
#define RK808_DVS1_POL		BIT(1)

/* Offset from XXX_ON_VSEL to XXX_SLP_VSEL */
#define RK808_SLP_REG_OFFSET 1

/* Offset from XXX_ON_VSEL to XXX_DVS_VSEL */
#define RK808_DVS_REG_OFFSET 2

/* Offset from XXX_EN_REG to SLEEP_SET_OFF_XXX */
#define RK808_SLP_SET_OFF_REG_OFFSET 2

/* max steps for increase voltage of Buck1/2, equal 100mv*/
#define MAX_STEPS_ONE_TIME 8

#define RK805_DESC(_id, _match, _supply, _min, _max, _step, _vreg,      \
	_vmask, _ereg, _emask, _etime)                                  \
	[_id] = {                                                       \
		.name           = (_match),                             \
		.supply_name    = (_supply),                            \
		.of_match       = of_match_ptr(_match),                 \
		.regulators_node = of_match_ptr("regulators"),          \
		.type           = REGULATOR_VOLTAGE,                    \
		.id             = (_id),                                \
		.n_voltages     = (((_max) - (_min)) / (_step) + 1),    \
		.owner          = THIS_MODULE,                          \
		.min_uV         = (_min) * 1000,                        \
		.uV_step        = (_step) * 1000,                       \
		.vsel_reg       = (_vreg),                              \
		.vsel_mask      = (_vmask),                             \
		.enable_reg     = (_ereg),                              \
		.enable_mask    = (_emask),                             \
		.enable_time    = (_etime),                             \
		.ops            = &rk805_reg_ops,                       \
	}

#define RK8XX_DESC(_id, _match, _supply, _min, _max, _step, _vreg,	\
	_vmask, _ereg, _emask, _etime)					\
	[_id] = {							\
		.name		= (_match),				\
		.supply_name	= (_supply),				\
		.of_match	= of_match_ptr(_match),			\
		.regulators_node = of_match_ptr("regulators"),		\
		.type		= REGULATOR_VOLTAGE,			\
		.id		= (_id),				\
		.n_voltages	= (((_max) - (_min)) / (_step) + 1),	\
		.owner		= THIS_MODULE,				\
		.min_uV		= (_min) * 1000,			\
		.uV_step	= (_step) * 1000,			\
		.vsel_reg	= (_vreg),				\
		.vsel_mask	= (_vmask),				\
		.enable_reg	= (_ereg),				\
		.enable_mask	= (_emask),				\
		.enable_time	= (_etime),				\
		.ops		= &rk808_reg_ops,			\
	}

#define RK8XX_DESC_SWITCH(_id, _match, _supply, _ereg, _emask)		\
	[_id] = {							\
		.name		= (_match),				\
		.supply_name	= (_supply),				\
		.of_match	= of_match_ptr(_match),			\
		.regulators_node = of_match_ptr("regulators"),		\
		.type		= REGULATOR_VOLTAGE,			\
		.id		= (_id),				\
		.enable_reg	= (_ereg),				\
		.enable_mask	= (_emask),				\
		.owner		= THIS_MODULE,				\
		.ops		= &rk808_switch_ops			\
	}


struct rk808_regulator_data {
	struct gpio_desc *dvs_gpio[2];
};

static const int rk808_buck_config_regs[] = {
	RK808_BUCK1_CONFIG_REG,
	RK808_BUCK2_CONFIG_REG,
	RK808_BUCK3_CONFIG_REG,
	RK808_BUCK4_CONFIG_REG,
};

static const struct regulator_linear_range rk808_ldo3_voltage_ranges[] = {
	REGULATOR_LINEAR_RANGE(800000, 0, 13, 100000),
	REGULATOR_LINEAR_RANGE(2500000, 15, 15, 0),
};

static int rk808_buck1_2_get_voltage_sel_regmap(struct regulator_dev *rdev)
{
	struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
	int id = rdev_get_id(rdev);
	struct gpio_desc *gpio = pdata->dvs_gpio[id];
	unsigned int val;
	int ret;

	if (!gpio || gpiod_get_value(gpio) == 0)
		return regulator_get_voltage_sel_regmap(rdev);

	ret = regmap_read(rdev->regmap,
			  rdev->desc->vsel_reg + RK808_DVS_REG_OFFSET,
			  &val);
	if (ret != 0)
		return ret;

	val &= rdev->desc->vsel_mask;
	val >>= ffs(rdev->desc->vsel_mask) - 1;

	return val;
}

static int rk808_buck1_2_i2c_set_voltage_sel(struct regulator_dev *rdev,
					     unsigned sel)
{
	int ret, delta_sel;
	unsigned int old_sel, tmp, val, mask = rdev->desc->vsel_mask;

	ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &val);
	if (ret != 0)
		return ret;

	tmp = val & ~mask;
	old_sel = val & mask;
	old_sel >>= ffs(mask) - 1;
	delta_sel = sel - old_sel;

	/*
	 * If directly modify the register to change the voltage, we will face
	 * the risk of overshoot. Put it into a multi-step, can effectively
	 * avoid this problem, a step is 100mv here.
	 */
	while (delta_sel > MAX_STEPS_ONE_TIME) {
		old_sel += MAX_STEPS_ONE_TIME;
		val = old_sel << (ffs(mask) - 1);
		val |= tmp;

		/*
		 * i2c is 400kHz (2.5us per bit) and we must transmit _at least_
		 * 3 bytes (24 bits) plus start and stop so 26 bits.  So we've
		 * got more than 65 us between each voltage change and thus
		 * won't ramp faster than ~1500 uV / us.
		 */
		ret = regmap_write(rdev->regmap, rdev->desc->vsel_reg, val);
		delta_sel = sel - old_sel;
	}

	sel <<= ffs(mask) - 1;
	val = tmp | sel;
	ret = regmap_write(rdev->regmap, rdev->desc->vsel_reg, val);

	/*
	 * When we change the voltage register directly, the ramp rate is about
	 * 100000uv/us, wait 1us to make sure the target voltage to be stable,
	 * so we needn't wait extra time after that.
	 */
	udelay(1);

	return ret;
}

static int rk808_buck1_2_set_voltage_sel(struct regulator_dev *rdev,
					 unsigned sel)
{
	struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
	int id = rdev_get_id(rdev);
	struct gpio_desc *gpio = pdata->dvs_gpio[id];
	unsigned int reg = rdev->desc->vsel_reg;
	unsigned old_sel;
	int ret, gpio_level;

	if (!gpio)
		return rk808_buck1_2_i2c_set_voltage_sel(rdev, sel);

	gpio_level = gpiod_get_value(gpio);
	if (gpio_level == 0) {
		reg += RK808_DVS_REG_OFFSET;
		ret = regmap_read(rdev->regmap, rdev->desc->vsel_reg, &old_sel);
	} else {
		ret = regmap_read(rdev->regmap,
				  reg + RK808_DVS_REG_OFFSET,
				  &old_sel);
	}

	if (ret != 0)
		return ret;

	sel <<= ffs(rdev->desc->vsel_mask) - 1;
	sel |= old_sel & ~rdev->desc->vsel_mask;

	ret = regmap_write(rdev->regmap, reg, sel);
	if (ret)
		return ret;

	gpiod_set_value(gpio, !gpio_level);

	return ret;
}

static int rk808_buck1_2_set_voltage_time_sel(struct regulator_dev *rdev,
				       unsigned int old_selector,
				       unsigned int new_selector)
{
	struct rk808_regulator_data *pdata = rdev_get_drvdata(rdev);
	int id = rdev_get_id(rdev);
	struct gpio_desc *gpio = pdata->dvs_gpio[id];

	/* if there is no dvs1/2 pin, we don't need wait extra time here. */
	if (!gpio)
		return 0;

	return regulator_set_voltage_time_sel(rdev, old_selector, new_selector);
}

static int rk808_set_ramp_delay(struct regulator_dev *rdev, int ramp_delay)
{
	unsigned int ramp_value = RK808_RAMP_RATE_10MV_PER_US;
	unsigned int reg = rk808_buck_config_regs[rdev_get_id(rdev)];

	switch (ramp_delay) {
	case 1 ... 2000:
		ramp_value = RK808_RAMP_RATE_2MV_PER_US;
		break;
	case 2001 ... 4000:
		ramp_value = RK808_RAMP_RATE_4MV_PER_US;
		break;
	case 4001 ... 6000:
		ramp_value = RK808_RAMP_RATE_6MV_PER_US;
		break;
	case 6001 ... 10000:
		break;
	default:
		pr_warn("%s ramp_delay: %d not supported, setting 10000\n",
			rdev->desc->name, ramp_delay);
	}

	return regmap_update_bits(rdev->regmap, reg,
				  RK808_RAMP_RATE_MASK, ramp_value);
}

static int rk808_set_suspend_voltage(struct regulator_dev *rdev, int uv)
{
	unsigned int reg;
	int sel = regulator_map_voltage_linear(rdev, uv, uv);

	if (sel < 0)
		return -EINVAL;

	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->vsel_mask,
				  sel);
}

static int rk808_set_suspend_voltage_range(struct regulator_dev *rdev, int uv)
{
	unsigned int reg;
	int sel = regulator_map_voltage_linear_range(rdev, uv, uv);

	if (sel < 0)
		return -EINVAL;

	reg = rdev->desc->vsel_reg + RK808_SLP_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->vsel_mask,
				  sel);
}

static int rk805_set_suspend_enable(struct regulator_dev *rdev)
{
	unsigned int reg;

	reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->enable_mask,
				  rdev->desc->enable_mask);
}

static int rk805_set_suspend_disable(struct regulator_dev *rdev)
{
	unsigned int reg;

	reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->enable_mask,
				  0);
}

static int rk808_set_suspend_enable(struct regulator_dev *rdev)
{
	unsigned int reg;

	reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->enable_mask,
				  0);
}

static int rk808_set_suspend_disable(struct regulator_dev *rdev)
{
	unsigned int reg;

	reg = rdev->desc->enable_reg + RK808_SLP_SET_OFF_REG_OFFSET;

	return regmap_update_bits(rdev->regmap, reg,
				  rdev->desc->enable_mask,
				  rdev->desc->enable_mask);
}

static const struct regulator_ops rk805_reg_ops = {
	.list_voltage           = regulator_list_voltage_linear,
	.map_voltage            = regulator_map_voltage_linear,
	.get_voltage_sel        = regulator_get_voltage_sel_regmap,
	.set_voltage_sel        = regulator_set_voltage_sel_regmap,
	.enable                 = regulator_enable_regmap,
	.disable                = regulator_disable_regmap,
	.is_enabled             = regulator_is_enabled_regmap,
	.set_suspend_voltage    = rk808_set_suspend_voltage,
	.set_suspend_enable     = rk805_set_suspend_enable,
	.set_suspend_disable    = rk805_set_suspend_disable,
};

static const struct regulator_ops rk805_switch_ops = {
	.enable                 = regulator_enable_regmap,
	.disable                = regulator_disable_regmap,
	.is_enabled             = regulator_is_enabled_regmap,
	.set_suspend_enable     = rk805_set_suspend_enable,
	.set_suspend_disable    = rk805_set_suspend_disable,
};

static const struct regulator_ops rk808_buck1_2_ops = {
	.list_voltage		= regulator_list_voltage_linear,
	.map_voltage		= regulator_map_voltage_linear,
	.get_voltage_sel	= rk808_buck1_2_get_voltage_sel_regmap,
	.set_voltage_sel	= rk808_buck1_2_set_voltage_sel,
	.set_voltage_time_sel	= rk808_buck1_2_set_voltage_time_sel,
	.enable			= regulator_enable_regmap,
	.disable		= regulator_disable_regmap,
	.is_enabled		= regulator_is_enabled_regmap,
	.set_ramp_delay		= rk808_set_ramp_delay,
	.set_suspend_voltage	= rk808_set_suspend_voltage,
	.set_suspend_enable	= rk808_set_suspend_enable,
	.set_suspend_disable	= rk808_set_suspend_disable,
};

static const struct regulator_ops rk808_reg_ops = {
	.list_voltage		= regulator_list_voltage_linear,
	.map_voltage		= regulator_map_voltage_linear,
	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
	.enable			= regulator_enable_regmap,
	.disable		= regulator_disable_regmap,
	.is_enabled		= regulator_is_enabled_regmap,
	.set_suspend_voltage	= rk808_set_suspend_voltage,
	.set_suspend_enable	= rk808_set_suspend_enable,
	.set_suspend_disable	= rk808_set_suspend_disable,
};

static const struct regulator_ops rk808_reg_ops_ranges = {
	.list_voltage		= regulator_list_voltage_linear_range,
	.map_voltage		= regulator_map_voltage_linear_range,
	.get_voltage_sel	= regulator_get_voltage_sel_regmap,
	.set_voltage_sel	= regulator_set_voltage_sel_regmap,
	.enable			= regulator_enable_regmap,
	.disable		= regulator_disable_regmap,
	.is_enabled		= regulator_is_enabled_regmap,
	.set_suspend_voltage	= rk808_set_suspend_voltage_range,
	.set_suspend_enable	= rk808_set_suspend_enable,
	.set_suspend_disable	= rk808_set_suspend_disable,
};

static const struct regulator_ops rk808_switch_ops = {
	.enable			= regulator_enable_regmap,
	.disable		= regulator_disable_regmap,
	.is_enabled		= regulator_is_enabled_regmap,
	.set_suspend_enable	= rk808_set_suspend_enable,
	.set_suspend_disable	= rk808_set_suspend_disable,
};

static const struct regulator_linear_range rk805_buck_1_2_voltage_ranges[] = {
	REGULATOR_LINEAR_RANGE(712500, 0, 59, 12500),
	REGULATOR_LINEAR_RANGE(1800000, 60, 62, 200000),
	REGULATOR_LINEAR_RANGE(2300000, 63, 63, 0),
};

static const struct regulator_desc rk805_reg[] = {
	{
		.name = "DCDC_REG1",
		.supply_name = "vcc1",
		.of_match = of_match_ptr("DCDC_REG1"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK805_ID_DCDC1,
		.ops = &rk808_reg_ops_ranges,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 64,
		.linear_ranges = rk805_buck_1_2_voltage_ranges,
		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
		.vsel_reg = RK805_BUCK1_ON_VSEL_REG,
		.vsel_mask = RK818_BUCK_VSEL_MASK,
		.enable_reg = RK805_DCDC_EN_REG,
		.enable_mask = BIT(0),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG2",
		.supply_name = "vcc2",
		.of_match = of_match_ptr("DCDC_REG2"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK805_ID_DCDC2,
		.ops = &rk808_reg_ops_ranges,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 64,
		.linear_ranges = rk805_buck_1_2_voltage_ranges,
		.n_linear_ranges = ARRAY_SIZE(rk805_buck_1_2_voltage_ranges),
		.vsel_reg = RK805_BUCK2_ON_VSEL_REG,
		.vsel_mask = RK818_BUCK_VSEL_MASK,
		.enable_reg = RK805_DCDC_EN_REG,
		.enable_mask = BIT(1),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG3",
		.supply_name = "vcc3",
		.of_match = of_match_ptr("DCDC_REG3"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK805_ID_DCDC3,
		.ops = &rk805_switch_ops,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 1,
		.enable_reg = RK805_DCDC_EN_REG,
		.enable_mask = BIT(2),
		.owner = THIS_MODULE,
	},

	RK805_DESC(RK805_ID_DCDC4, "DCDC_REG4", "vcc4", 800, 3400, 100,
		RK805_BUCK4_ON_VSEL_REG, RK818_BUCK4_VSEL_MASK,
		RK805_DCDC_EN_REG, BIT(3), 0),

	RK805_DESC(RK805_ID_LDO1, "LDO_REG1", "vcc5", 800, 3400, 100,
		RK805_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
		BIT(0), 400),
	RK805_DESC(RK805_ID_LDO2, "LDO_REG2", "vcc5", 800, 3400, 100,
		RK805_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
		BIT(1), 400),
	RK805_DESC(RK805_ID_LDO3, "LDO_REG3", "vcc6", 800, 3400, 100,
		RK805_LDO3_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK805_LDO_EN_REG,
		BIT(2), 400),
};

static const struct regulator_desc rk808_reg[] = {
	{
		.name = "DCDC_REG1",
		.supply_name = "vcc1",
		.of_match = of_match_ptr("DCDC_REG1"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK808_ID_DCDC1,
		.ops = &rk808_buck1_2_ops,
		.type = REGULATOR_VOLTAGE,
		.min_uV = 712500,
		.uV_step = 12500,
		.n_voltages = 64,
		.vsel_reg = RK808_BUCK1_ON_VSEL_REG,
		.vsel_mask = RK808_BUCK_VSEL_MASK,
		.enable_reg = RK808_DCDC_EN_REG,
		.enable_mask = BIT(0),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG2",
		.supply_name = "vcc2",
		.of_match = of_match_ptr("DCDC_REG2"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK808_ID_DCDC2,
		.ops = &rk808_buck1_2_ops,
		.type = REGULATOR_VOLTAGE,
		.min_uV = 712500,
		.uV_step = 12500,
		.n_voltages = 64,
		.vsel_reg = RK808_BUCK2_ON_VSEL_REG,
		.vsel_mask = RK808_BUCK_VSEL_MASK,
		.enable_reg = RK808_DCDC_EN_REG,
		.enable_mask = BIT(1),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG3",
		.supply_name = "vcc3",
		.of_match = of_match_ptr("DCDC_REG3"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK808_ID_DCDC3,
		.ops = &rk808_switch_ops,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 1,
		.enable_reg = RK808_DCDC_EN_REG,
		.enable_mask = BIT(2),
		.owner = THIS_MODULE,
	},
	RK8XX_DESC(RK808_ID_DCDC4, "DCDC_REG4", "vcc4", 1800, 3300, 100,
		RK808_BUCK4_ON_VSEL_REG, RK808_BUCK4_VSEL_MASK,
		RK808_DCDC_EN_REG, BIT(3), 0),
	RK8XX_DESC(RK808_ID_LDO1, "LDO_REG1", "vcc6", 1800, 3400, 100,
		RK808_LDO1_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(0), 400),
	RK8XX_DESC(RK808_ID_LDO2, "LDO_REG2", "vcc6", 1800, 3400, 100,
		RK808_LDO2_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(1), 400),
	{
		.name = "LDO_REG3",
		.supply_name = "vcc7",
		.of_match = of_match_ptr("LDO_REG3"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK808_ID_LDO3,
		.ops = &rk808_reg_ops_ranges,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 16,
		.linear_ranges = rk808_ldo3_voltage_ranges,
		.n_linear_ranges = ARRAY_SIZE(rk808_ldo3_voltage_ranges),
		.vsel_reg = RK808_LDO3_ON_VSEL_REG,
		.vsel_mask = RK808_BUCK4_VSEL_MASK,
		.enable_reg = RK808_LDO_EN_REG,
		.enable_mask = BIT(2),
		.enable_time = 400,
		.owner = THIS_MODULE,
	},
	RK8XX_DESC(RK808_ID_LDO4, "LDO_REG4", "vcc9", 1800, 3400, 100,
		RK808_LDO4_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(3), 400),
	RK8XX_DESC(RK808_ID_LDO5, "LDO_REG5", "vcc9", 1800, 3400, 100,
		RK808_LDO5_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(4), 400),
	RK8XX_DESC(RK808_ID_LDO6, "LDO_REG6", "vcc10", 800, 2500, 100,
		RK808_LDO6_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(5), 400),
	RK8XX_DESC(RK808_ID_LDO7, "LDO_REG7", "vcc7", 800, 2500, 100,
		RK808_LDO7_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(6), 400),
	RK8XX_DESC(RK808_ID_LDO8, "LDO_REG8", "vcc11", 1800, 3400, 100,
		RK808_LDO8_ON_VSEL_REG, RK808_LDO_VSEL_MASK, RK808_LDO_EN_REG,
		BIT(7), 400),
	RK8XX_DESC_SWITCH(RK808_ID_SWITCH1, "SWITCH_REG1", "vcc8",
		RK808_DCDC_EN_REG, BIT(5)),
	RK8XX_DESC_SWITCH(RK808_ID_SWITCH2, "SWITCH_REG2", "vcc12",
		RK808_DCDC_EN_REG, BIT(6)),
};

static const struct regulator_desc rk818_reg[] = {
	{
		.name = "DCDC_REG1",
		.supply_name = "vcc1",
		.of_match = of_match_ptr("DCDC_REG1"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK818_ID_DCDC1,
		.ops = &rk808_reg_ops,
		.type = REGULATOR_VOLTAGE,
		.min_uV = 712500,
		.uV_step = 12500,
		.n_voltages = 64,
		.vsel_reg = RK818_BUCK1_ON_VSEL_REG,
		.vsel_mask = RK818_BUCK_VSEL_MASK,
		.enable_reg = RK818_DCDC_EN_REG,
		.enable_mask = BIT(0),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG2",
		.supply_name = "vcc2",
		.of_match = of_match_ptr("DCDC_REG2"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK818_ID_DCDC2,
		.ops = &rk808_reg_ops,
		.type = REGULATOR_VOLTAGE,
		.min_uV = 712500,
		.uV_step = 12500,
		.n_voltages = 64,
		.vsel_reg = RK818_BUCK2_ON_VSEL_REG,
		.vsel_mask = RK818_BUCK_VSEL_MASK,
		.enable_reg = RK818_DCDC_EN_REG,
		.enable_mask = BIT(1),
		.owner = THIS_MODULE,
	}, {
		.name = "DCDC_REG3",
		.supply_name = "vcc3",
		.of_match = of_match_ptr("DCDC_REG3"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK818_ID_DCDC3,
		.ops = &rk808_switch_ops,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 1,
		.enable_reg = RK818_DCDC_EN_REG,
		.enable_mask = BIT(2),
		.owner = THIS_MODULE,
	},
	RK8XX_DESC(RK818_ID_DCDC4, "DCDC_REG4", "vcc4", 1800, 3600, 100,
		RK818_BUCK4_ON_VSEL_REG, RK818_BUCK4_VSEL_MASK,
		RK818_DCDC_EN_REG, BIT(3), 0),
	RK8XX_DESC(RK818_ID_BOOST, "DCDC_BOOST", "boost", 4700, 5400, 100,
		RK818_BOOST_LDO9_ON_VSEL_REG, RK818_BOOST_ON_VSEL_MASK,
		RK818_DCDC_EN_REG, BIT(4), 0),
	RK8XX_DESC(RK818_ID_LDO1, "LDO_REG1", "vcc6", 1800, 3400, 100,
		RK818_LDO1_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(0), 400),
	RK8XX_DESC(RK818_ID_LDO2, "LDO_REG2", "vcc6", 1800, 3400, 100,
		RK818_LDO2_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(1), 400),
	{
		.name = "LDO_REG3",
		.supply_name = "vcc7",
		.of_match = of_match_ptr("LDO_REG3"),
		.regulators_node = of_match_ptr("regulators"),
		.id = RK818_ID_LDO3,
		.ops = &rk808_reg_ops_ranges,
		.type = REGULATOR_VOLTAGE,
		.n_voltages = 16,
		.linear_ranges = rk808_ldo3_voltage_ranges,
		.n_linear_ranges = ARRAY_SIZE(rk808_ldo3_voltage_ranges),
		.vsel_reg = RK818_LDO3_ON_VSEL_REG,
		.vsel_mask = RK818_LDO3_ON_VSEL_MASK,
		.enable_reg = RK818_LDO_EN_REG,
		.enable_mask = BIT(2),
		.enable_time = 400,
		.owner = THIS_MODULE,
	},
	RK8XX_DESC(RK818_ID_LDO4, "LDO_REG4", "vcc8", 1800, 3400, 100,
		RK818_LDO4_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(3), 400),
	RK8XX_DESC(RK818_ID_LDO5, "LDO_REG5", "vcc7", 1800, 3400, 100,
		RK818_LDO5_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(4), 400),
	RK8XX_DESC(RK818_ID_LDO6, "LDO_REG6", "vcc8", 800, 2500, 100,
		RK818_LDO6_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(5), 400),
	RK8XX_DESC(RK818_ID_LDO7, "LDO_REG7", "vcc7", 800, 2500, 100,
		RK818_LDO7_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(6), 400),
	RK8XX_DESC(RK818_ID_LDO8, "LDO_REG8", "vcc8", 1800, 3400, 100,
		RK818_LDO8_ON_VSEL_REG, RK818_LDO_VSEL_MASK, RK818_LDO_EN_REG,
		BIT(7), 400),
	RK8XX_DESC(RK818_ID_LDO9, "LDO_REG9", "vcc9", 1800, 3400, 100,
		RK818_BOOST_LDO9_ON_VSEL_REG, RK818_LDO_VSEL_MASK,
		RK818_DCDC_EN_REG, BIT(5), 400),
	RK8XX_DESC_SWITCH(RK818_ID_SWITCH, "SWITCH_REG", "vcc9",
		RK818_DCDC_EN_REG, BIT(6)),
	RK8XX_DESC_SWITCH(RK818_ID_HDMI_SWITCH, "HDMI_SWITCH", "h_5v",
		RK818_H5V_EN_REG, BIT(0)),
	RK8XX_DESC_SWITCH(RK818_ID_OTG_SWITCH, "OTG_SWITCH", "usb",
		RK818_DCDC_EN_REG, BIT(7)),
};

static int rk808_regulator_dt_parse_pdata(struct device *dev,
				   struct device *client_dev,
				   struct regmap *map,
				   struct rk808_regulator_data *pdata)
{
	struct device_node *np;
	int tmp, ret = 0, i;

	np = of_get_child_by_name(client_dev->of_node, "regulators");
	if (!np)
		return -ENXIO;

	for (i = 0; i < ARRAY_SIZE(pdata->dvs_gpio); i++) {
		pdata->dvs_gpio[i] =
			devm_gpiod_get_index_optional(client_dev, "dvs", i,
						      GPIOD_OUT_LOW);
		if (IS_ERR(pdata->dvs_gpio[i])) {
			ret = PTR_ERR(pdata->dvs_gpio[i]);
			dev_err(dev, "failed to get dvs%d gpio (%d)\n", i, ret);
			goto dt_parse_end;
		}

		if (!pdata->dvs_gpio[i]) {
			dev_warn(dev, "there is no dvs%d gpio\n", i);
			continue;
		}

		tmp = i ? RK808_DVS2_POL : RK808_DVS1_POL;
		ret = regmap_update_bits(map, RK808_IO_POL_REG, tmp,
				gpiod_is_active_low(pdata->dvs_gpio[i]) ?
				0 : tmp);
	}

dt_parse_end:
	of_node_put(np);
	return ret;
}

static int rk808_regulator_probe(struct platform_device *pdev)
{
	struct rk808 *rk808 = dev_get_drvdata(pdev->dev.parent);
	struct i2c_client *client = rk808->i2c;
	struct regulator_config config = {};
	struct regulator_dev *rk808_rdev;
	struct rk808_regulator_data *pdata;
	const struct regulator_desc *regulators;
	int ret, i, nregulators;

	pdata = devm_kzalloc(&pdev->dev, sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
		return -ENOMEM;

	ret = rk808_regulator_dt_parse_pdata(&pdev->dev, &client->dev,
					     rk808->regmap, pdata);
	if (ret < 0)
		return ret;

	platform_set_drvdata(pdev, pdata);

	switch (rk808->variant) {
	case RK805_ID:
		regulators = rk805_reg;
		nregulators = RK805_NUM_REGULATORS;
		break;
	case RK808_ID:
		regulators = rk808_reg;
		nregulators = RK808_NUM_REGULATORS;
		break;
	case RK818_ID:
		regulators = rk818_reg;
		nregulators = RK818_NUM_REGULATORS;
		break;
	default:
		dev_err(&client->dev, "unsupported RK8XX ID %lu\n",
			rk808->variant);
		return -EINVAL;
	}

	config.dev = &client->dev;
	config.driver_data = pdata;
	config.regmap = rk808->regmap;

	/* Instantiate the regulators */
	for (i = 0; i < nregulators; i++) {
		rk808_rdev = devm_regulator_register(&pdev->dev,
						     &regulators[i], &config);
		if (IS_ERR(rk808_rdev)) {
			dev_err(&client->dev,
				"failed to register %d regulator\n", i);
			return PTR_ERR(rk808_rdev);
		}
	}

	return 0;
}

static struct platform_driver rk808_regulator_driver = {
	.probe = rk808_regulator_probe,
	.driver = {
		.name = "rk808-regulator"
	},
};

module_platform_driver(rk808_regulator_driver);

MODULE_DESCRIPTION("regulator driver for the RK805/RK808/RK818 series PMICs");
MODULE_AUTHOR("Chris Zhong <zyw@rock-chips.com>");
MODULE_AUTHOR("Zhang Qing <zhangqing@rock-chips.com>");
MODULE_AUTHOR("Wadim Egorov <w.egorov@phytec.de>");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:rk808-regulator");