| # SPDX-License-Identifier: GPL-2.0-only |
| %YAML 1.2 |
| --- |
| $id: http://devicetree.org/schemas/connector/usb-connector.yaml# |
| $schema: http://devicetree.org/meta-schemas/core.yaml# |
| |
| title: USB Connector |
| |
| maintainers: |
| - Rob Herring <robh@kernel.org> |
| |
| description: |
| A USB connector node represents a physical USB connector. It should be a child |
| of a USB interface controller or a separate node when it is attached to both |
| MUX and USB interface controller. |
| |
| properties: |
| compatible: |
| oneOf: |
| - enum: |
| - usb-a-connector |
| - usb-b-connector |
| - usb-c-connector |
| |
| - items: |
| - const: gpio-usb-b-connector |
| - const: usb-b-connector |
| |
| - items: |
| - const: samsung,usb-connector-11pin |
| - const: usb-b-connector |
| |
| label: |
| description: Symbolic name for the connector. |
| |
| type: |
| description: Size of the connector, should be specified in case of |
| non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible |
| connectors. |
| $ref: /schemas/types.yaml#/definitions/string |
| |
| enum: |
| - mini |
| - micro |
| |
| self-powered: |
| description: Set this property if the USB device has its own power source. |
| type: boolean |
| |
| # The following are optional properties for "usb-b-connector". |
| id-gpios: |
| description: An input gpio for USB ID pin. |
| maxItems: 1 |
| |
| vbus-gpios: |
| description: An input gpio for USB VBus pin, used to detect presence of |
| VBUS 5V. |
| maxItems: 1 |
| |
| vbus-supply: |
| description: A phandle to the regulator for USB VBUS if needed when host |
| mode or dual role mode is supported. |
| Particularly, if use an output GPIO to control a VBUS regulator, should |
| model it as a regulator. See bindings/regulator/fixed-regulator.yaml |
| |
| # The following are optional properties for "usb-c-connector". |
| power-role: |
| description: Determines the power role that the Type C connector will |
| support. "dual" refers to Dual Role Port (DRP). |
| $ref: /schemas/types.yaml#/definitions/string |
| |
| enum: |
| - source |
| - sink |
| - dual |
| |
| try-power-role: |
| description: Preferred power role. |
| $ref: /schemas/types.yaml#/definitions/string |
| |
| enum: |
| - source |
| - sink |
| - dual |
| |
| data-role: |
| description: Data role if Type C connector supports USB data. "dual" refers |
| Dual Role Device (DRD). |
| $ref: /schemas/types.yaml#/definitions/string |
| |
| enum: |
| - host |
| - device |
| - dual |
| |
| typec-power-opmode: |
| description: Determines the power operation mode that the Type C connector |
| will support and will advertise through CC pins when it has no power |
| delivery support. |
| - "default" corresponds to default USB voltage and current defined by the |
| USB 2.0 and USB 3.2 specifications, 5V 500mA for USB 2.0 ports and |
| 5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane |
| operation respectively. |
| - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB |
| Type-C Cable and Connector specification, when Power Delivery is not |
| supported. |
| allOf: |
| - $ref: /schemas/types.yaml#/definitions/string |
| enum: |
| - default |
| - 1.5A |
| - 3.0A |
| |
| # The following are optional properties for "usb-c-connector" with power |
| # delivery support. |
| source-pdos: |
| description: An array of u32 with each entry providing supported power |
| source data object(PDO), the detailed bit definitions of PDO can be found |
| in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2 |
| Source_Capabilities Message, the order of each entry(PDO) should follow |
| the PD spec chapter 6.4.1. Required for power source and power dual role. |
| User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() |
| defined in dt-bindings/usb/pd.h. |
| minItems: 1 |
| maxItems: 7 |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| sink-pdos: |
| description: An array of u32 with each entry providing supported power sink |
| data object(PDO), the detailed bit definitions of PDO can be found in |
| "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3 |
| Sink Capabilities Message, the order of each entry(PDO) should follow the |
| PD spec chapter 6.4.1. Required for power sink and power dual role. User |
| can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined |
| in dt-bindings/usb/pd.h. |
| minItems: 1 |
| maxItems: 7 |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| sink-vdos: |
| description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), |
| providing additional information corresponding to the product, the detailed bit |
| definitions and the order of each VDO can be found in |
| "USB Power Delivery Specification Revision 3.0, Version 2.0 + ECNs 2020-12-10" |
| chapter 6.4.4.3.1 Discover Identity. User can specify the VDO array via |
| VDO_IDH/_CERT/_PRODUCT/_UFP/_DFP/_PCABLE/_ACABLE(1/2)/_VPD() defined in |
| dt-bindings/usb/pd.h. |
| minItems: 3 |
| maxItems: 6 |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| sink-vdos-v1: |
| description: An array of u32 with each entry, a Vendor Defined Message Object (VDO), |
| providing additional information corresponding to the product, the detailed bit |
| definitions and the order of each VDO can be found in |
| "USB Power Delivery Specification Revision 2.0, Version 1.3" chapter 6.4.4.3.1 Discover |
| Identity. User can specify the VDO array via VDO_IDH/_CERT/_PRODUCT/_CABLE/_AMA defined in |
| dt-bindings/usb/pd.h. |
| minItems: 3 |
| maxItems: 6 |
| $ref: /schemas/types.yaml#/definitions/uint32-array |
| |
| op-sink-microwatt: |
| description: Sink required operating power in microwatt, if source can't |
| offer the power, Capability Mismatch is set. Required for power sink and |
| power dual role. |
| |
| ports: |
| $ref: /schemas/graph.yaml#/properties/ports |
| description: OF graph bindings modeling any data bus to the connector |
| unless the bus is between parent node and the connector. Since a single |
| connector can have multiple data buses every bus has an assigned OF graph |
| port number as described below. |
| |
| properties: |
| port@0: |
| $ref: /schemas/graph.yaml#/properties/port |
| description: High Speed (HS), present in all connectors. |
| |
| port@1: |
| $ref: /schemas/graph.yaml#/properties/port |
| description: Super Speed (SS), present in SS capable connectors. |
| |
| port@2: |
| $ref: /schemas/graph.yaml#/properties/port |
| description: Sideband Use (SBU), present in USB-C. This describes the |
| alternate mode connection of which SBU is a part. |
| |
| required: |
| - port@0 |
| |
| new-source-frs-typec-current: |
| description: Initial current capability of the new source when vSafe5V |
| is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink" |
| of "USB Power Delivery Specification Revision 3.0, Version 1.2" provides the |
| different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current" |
| provides a detailed description of the field. The sink PDO from current source |
| reflects the current source's(i.e. transmitter of the FRS signal) power |
| requirement during fr swap. The current sink (i.e. receiver of the FRS signal), |
| a.k.a new source, should check if it will be able to satisfy the current source's, |
| new sink's, requirement during frswap before enabling the frs signal reception. |
| This property refers to maximum current capability that the current sink can |
| satisfy. During FRS, VBUS voltage is at 5V, as the partners are in implicit |
| contract, hence, the power level is only a function of the current capability. |
| "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink". |
| "2" refers to 1.5A@5V. |
| "3" refers to 3.0A@5V. |
| $ref: /schemas/types.yaml#/definitions/uint32 |
| enum: [1, 2, 3] |
| |
| slow-charger-loop: |
| description: Allows PMIC charger loops which are slow(i.e. cannot meet the 15ms deadline) to |
| still comply to pSnkStby i.e Maximum power that can be consumed by sink while in Sink Standby |
| state as defined in 7.4.2 Sink Electrical Parameters of USB Power Delivery Specification |
| Revision 3.0, Version 1.2. When the property is set, the port requests pSnkStby(2.5W - |
| 5V@500mA) upon entering SNK_DISCOVERY(instead of 3A or the 1.5A, Rp current advertised, during |
| SNK_DISCOVERY) and the actual currrent limit after reception of PS_Ready for PD link or during |
| SNK_READY for non-pd link. |
| type: boolean |
| |
| dependencies: |
| sink-vdos-v1: [ 'sink-vdos' ] |
| sink-vdos: [ 'sink-vdos-v1' ] |
| |
| required: |
| - compatible |
| |
| allOf: |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: gpio-usb-b-connector |
| then: |
| anyOf: |
| - required: |
| - vbus-gpios |
| - required: |
| - id-gpios |
| |
| - if: |
| properties: |
| compatible: |
| contains: |
| const: samsung,usb-connector-11pin |
| then: |
| properties: |
| type: |
| const: micro |
| |
| anyOf: |
| - not: |
| required: |
| - typec-power-opmode |
| - new-source-frs-typec-current |
| |
| additionalProperties: true |
| |
| examples: |
| # Micro-USB connector with HS lines routed via controller (MUIC). |
| - | |
| muic-max77843 { |
| usb_con1: connector { |
| compatible = "usb-b-connector"; |
| label = "micro-USB"; |
| type = "micro"; |
| }; |
| }; |
| |
| # USB-C connector attached to CC controller (s2mm005), HS lines routed |
| # to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort. |
| # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY. |
| - | |
| ccic: s2mm005 { |
| usb_con2: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| usb_con_hs: endpoint { |
| remote-endpoint = <&max77865_usbc_hs>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| usb_con_ss: endpoint { |
| remote-endpoint = <&usbdrd_phy_ss>; |
| }; |
| }; |
| port@2 { |
| reg = <2>; |
| usb_con_sbu: endpoint { |
| remote-endpoint = <&dp_aux>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| # USB-C connector attached to a typec port controller(ptn5110), which has |
| # power delivery support and enables drp. |
| - | |
| #include <dt-bindings/usb/pd.h> |
| typec: ptn5110 { |
| usb_con3: connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| power-role = "dual"; |
| try-power-role = "sink"; |
| source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>; |
| sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM) |
| PDO_VAR(5000, 12000, 2000)>; |
| op-sink-microwatt = <10000000>; |
| }; |
| }; |
| |
| # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220) |
| # with SS 2:1 MUX. HS lines routed to SoC, SS lines routed to the MUX and |
| # the output of MUX is connected to the SoC. |
| - | |
| connector { |
| compatible = "usb-c-connector"; |
| label = "USB-C"; |
| data-role = "dual"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| port@0 { |
| reg = <0>; |
| hs_ep: endpoint { |
| remote-endpoint = <&usb3_hs_ep>; |
| }; |
| }; |
| port@1 { |
| reg = <1>; |
| ss_ep: endpoint { |
| remote-endpoint = <&hd3ss3220_in_ep>; |
| }; |
| }; |
| }; |
| }; |
| |
| # USB connector with GPIO control lines |
| - | |
| #include <dt-bindings/gpio/gpio.h> |
| |
| usb { |
| connector { |
| compatible = "gpio-usb-b-connector", "usb-b-connector"; |
| type = "micro"; |
| id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>; |
| vbus-supply = <&usb_p0_vbus>; |
| }; |
| }; |
| |
| # Micro-USB connector with HS lines routed via controller (MUIC) and MHL |
| # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based |
| # mobile phone |
| - | |
| muic-max77843 { |
| usb_con4: connector { |
| compatible = "samsung,usb-connector-11pin", "usb-b-connector"; |
| label = "micro-USB"; |
| type = "micro"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| muic_to_usb: endpoint { |
| remote-endpoint = <&usb_to_muic>; |
| }; |
| }; |
| port@3 { |
| reg = <3>; |
| usb_con_mhl: endpoint { |
| remote-endpoint = <&sii8620_mhl>; |
| }; |
| }; |
| }; |
| }; |
| }; |
