blob: bd4aab6092e0f9b2f859e8d3e8ee3ee2178ed889 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Device tree for the uDPU board.
* Based on Marvell Armada 3720 development board (DB-88F3720-DDR3)
* Copyright (C) 2016 Marvell
* Copyright (C) 2019 Methode Electronics
* Copyright (C) 2019 Telus
*
* Vladimir Vid <vladimir.vid@sartura.hr>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-372x.dtsi"
/ {
model = "Methode uDPU Board";
compatible = "methode,udpu", "marvell,armada3720";
chosen {
stdout-path = "serial0:115200n8";
};
memory@0 {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
leds {
pinctrl-names = "default";
compatible = "gpio-leds";
power1 {
label = "udpu:green:power";
gpios = <&gpionb 11 GPIO_ACTIVE_LOW>;
};
power2 {
label = "udpu:red:power";
gpios = <&gpionb 12 GPIO_ACTIVE_LOW>;
};
network1 {
label = "udpu:green:network";
gpios = <&gpionb 13 GPIO_ACTIVE_LOW>;
};
network2 {
label = "udpu:red:network";
gpios = <&gpionb 14 GPIO_ACTIVE_LOW>;
};
alarm1 {
label = "udpu:green:alarm";
gpios = <&gpionb 15 GPIO_ACTIVE_LOW>;
};
alarm2 {
label = "udpu:red:alarm";
gpios = <&gpionb 16 GPIO_ACTIVE_LOW>;
};
};
sfp_eth0: sfp-eth0 {
compatible = "sff,sfp";
i2c-bus = <&i2c0>;
los-gpio = <&gpiosb 2 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 3 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 4 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 5 GPIO_ACTIVE_HIGH>;
};
sfp_eth1: sfp-eth1 {
compatible = "sff,sfp";
i2c-bus = <&i2c1>;
los-gpio = <&gpiosb 7 GPIO_ACTIVE_HIGH>;
mod-def0-gpio = <&gpiosb 8 GPIO_ACTIVE_LOW>;
tx-disable-gpio = <&gpiosb 9 GPIO_ACTIVE_HIGH>;
tx-fault-gpio = <&gpiosb 10 GPIO_ACTIVE_HIGH>;
};
};
&sdhci0 {
status = "okay";
bus-width = <8>;
mmc-ddr-1_8v;
mmc-hs400-1_8v;
marvell,pad-type = "fixed-1-8v";
non-removable;
no-sd;
no-sdio;
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_quad_pins>;
m25p80@0 {
compatible = "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <54000000>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
/* only bootloader is located on the SPI */
partition@0 {
label = "uboot";
reg = <0 0x400000>;
};
};
};
};
&i2c0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
};
&i2c1 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c2_pins>;
lm75@48 {
status = "okay";
compatible = "lm75";
reg = <0x48>;
};
lm75@49 {
status = "okay";
compatible = "lm75";
reg = <0x49>;
};
};
&eth0 {
phy-mode = "sgmii";
status = "okay";
managed = "in-band-status";
sfp = <&sfp_eth0>;
};
&eth1 {
phy-mode = "sgmii";
status = "okay";
managed = "in-band-status";
sfp = <&sfp_eth1>;
};
&usb3 {
status = "okay";
};
&uart0 {
status = "okay";
};