# SPDX-License-Identifier: GPL-2.0-only
%YAML 1.2
---
$id: http://devicetree.org/schemas/connector/usb-connector.yaml#
$schema: http://devicetree.org/meta-schemas/core.yaml#

title: USB Connector

maintainers:
  - Rob Herring <robh@kernel.org>

description:
  A USB connector node represents a physical USB connector. It should be a child
  of a USB interface controller or a separate node when it is attached to both
  MUX and USB interface controller.

properties:
  compatible:
    oneOf:
      - enum:
          - usb-a-connector
          - usb-b-connector
          - usb-c-connector

      - items:
          - const: gpio-usb-b-connector
          - const: usb-b-connector

      - items:
          - const: samsung,usb-connector-11pin
          - const: usb-b-connector

  label:
    description: Symbolic name for the connector.

  type:
    description: Size of the connector, should be specified in case of
      non-fullsize 'usb-a-connector' or 'usb-b-connector' compatible
      connectors.
    $ref: /schemas/types.yaml#/definitions/string

    enum:
      - mini
      - micro

  self-powered:
    description: Set this property if the USB device has its own power source.
    type: boolean

  # The following are optional properties for "usb-b-connector".
  id-gpios:
    description: An input gpio for USB ID pin.
    maxItems: 1

  vbus-gpios:
    description: An input gpio for USB VBus pin, used to detect presence of
      VBUS 5V.
    maxItems: 1

  vbus-supply:
    description: A phandle to the regulator for USB VBUS if needed when host
      mode or dual role mode is supported.
      Particularly, if use an output GPIO to control a VBUS regulator, should
      model it as a regulator. See bindings/regulator/fixed-regulator.yaml

  # The following are optional properties for "usb-c-connector".
  power-role:
    description: Determines the power role that the Type C connector will
      support. "dual" refers to Dual Role Port (DRP).
    $ref: /schemas/types.yaml#/definitions/string

    enum:
      - source
      - sink
      - dual

  try-power-role:
    description: Preferred power role.
    $ref: /schemas/types.yaml#/definitions/string

    enum:
      - source
      - sink
      - dual

  data-role:
    description: Data role if Type C connector supports USB data. "dual" refers
      Dual Role Device (DRD).
    $ref: /schemas/types.yaml#/definitions/string

    enum:
      - host
      - device
      - dual

  typec-power-opmode:
    description: Determines the power operation mode that the Type C connector
      will support and will advertise through CC pins when it has no power
      delivery support.
      - "default" corresponds to default USB voltage and current defined by the
        USB 2.0 and USB 3.2 specifications, 5V 500mA for USB 2.0 ports and
        5V 900mA or 1500mA for USB 3.2 ports in single-lane or dual-lane
        operation respectively.
      - "1.5A" and "3.0A", 5V 1.5A and 5V 3.0A respectively, as defined in USB
        Type-C Cable and Connector specification, when Power Delivery is not
        supported.
    allOf:
      - $ref: /schemas/types.yaml#/definitions/string
    enum:
      - default
      - 1.5A
      - 3.0A

  # The following are optional properties for "usb-c-connector" with power
  # delivery support.
  source-pdos:
    description: An array of u32 with each entry providing supported power
      source data object(PDO), the detailed bit definitions of PDO can be found
      in "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.2
      Source_Capabilities Message, the order of each entry(PDO) should follow
      the PD spec chapter 6.4.1. Required for power source and power dual role.
      User can specify the source PDO array via PDO_FIXED/BATT/VAR/PPS_APDO()
      defined in dt-bindings/usb/pd.h.
    minItems: 1
    maxItems: 7
    $ref: /schemas/types.yaml#/definitions/uint32-array

  sink-pdos:
    description: An array of u32 with each entry providing supported power sink
      data object(PDO), the detailed bit definitions of PDO can be found in
      "Universal Serial Bus Power Delivery Specification" chapter 6.4.1.3
      Sink Capabilities Message, the order of each entry(PDO) should follow the
      PD spec chapter 6.4.1. Required for power sink and power dual role. User
      can specify the sink PDO array via PDO_FIXED/BATT/VAR/PPS_APDO() defined
      in dt-bindings/usb/pd.h.
    minItems: 1
    maxItems: 7
    $ref: /schemas/types.yaml#/definitions/uint32-array

  op-sink-microwatt:
    description: Sink required operating power in microwatt, if source can't
      offer the power, Capability Mismatch is set. Required for power sink and
      power dual role.

  ports:
    description: OF graph bindings (specified in bindings/graph.txt) that model
      any data bus to the connector unless the bus is between parent node and
      the connector. Since a single connector can have multiple data buses every
      bus has an assigned OF graph port number as described below.
    type: object
    properties:
      port@0:
        type: object
        description: High Speed (HS), present in all connectors.

      port@1:
        type: object
        description: Super Speed (SS), present in SS capable connectors.

      port@2:
        type: object
        description: Sideband Use (SBU), present in USB-C. This describes the
          alternate mode connection of which SBU is a part.

    required:
      - port@0

  new-source-frs-typec-current:
    description: Initial current capability of the new source when vSafe5V
      is applied during PD3.0 Fast Role Swap. "Table 6-14 Fixed Supply PDO - Sink"
      of "USB Power Delivery Specification Revision 3.0, Version 1.2" provides the
      different power levels and "6.4.1.3.1.6 Fast Role Swap USB Type-C Current"
      provides a detailed description of the field. The sink PDO from current source
      reflects the current source's(i.e. transmitter of the FRS signal) power
      requirement during fr swap. The current sink (i.e. receiver of the FRS signal),
      a.k.a new source, should check if it will be able to satisfy the current source's,
      new sink's, requirement during frswap before enabling the frs signal reception.
      This property refers to maximum current capability that the current sink can
      satisfy. During FRS, VBUS voltage is at 5V, as the partners are in implicit
      contract, hence, the power level is only a function of the current capability.
      "1" refers to default USB power level as described by "Table 6-14 Fixed Supply PDO - Sink".
      "2" refers to 1.5A@5V.
      "3" refers to 3.0A@5V.
    $ref: /schemas/types.yaml#/definitions/uint32
    enum: [1, 2, 3]

required:
  - compatible

allOf:
  - if:
      properties:
        compatible:
          contains:
            const: gpio-usb-b-connector
    then:
      anyOf:
        - required:
            - vbus-gpios
        - required:
            - id-gpios

  - if:
      properties:
        compatible:
          contains:
            const: samsung,usb-connector-11pin
    then:
      properties:
        type:
          const: micro

anyOf:
  - not:
      required:
        - typec-power-opmode
        - new-source-frs-typec-current

additionalProperties: true

examples:
  # Micro-USB connector with HS lines routed via controller (MUIC).
  - |
    muic-max77843 {
      usb_con1: connector {
        compatible = "usb-b-connector";
        label = "micro-USB";
        type = "micro";
      };
    };

  # USB-C connector attached to CC controller (s2mm005), HS lines routed
  # to companion PMIC (max77865), SS lines to USB3 PHY and SBU to DisplayPort.
  # DisplayPort video lines are routed to the connector via SS mux in USB3 PHY.
  - |
    ccic: s2mm005 {
      usb_con2: connector {
        compatible = "usb-c-connector";
        label = "USB-C";

        ports {
          #address-cells = <1>;
          #size-cells = <0>;

          port@0 {
            reg = <0>;
            usb_con_hs: endpoint {
              remote-endpoint = <&max77865_usbc_hs>;
            };
          };
          port@1 {
            reg = <1>;
            usb_con_ss: endpoint {
              remote-endpoint = <&usbdrd_phy_ss>;
            };
          };
          port@2 {
            reg = <2>;
            usb_con_sbu: endpoint {
              remote-endpoint = <&dp_aux>;
            };
          };
        };
      };
    };

  # USB-C connector attached to a typec port controller(ptn5110), which has
  # power delivery support and enables drp.
  - |
    #include <dt-bindings/usb/pd.h>
    typec: ptn5110 {
      usb_con3: connector {
        compatible = "usb-c-connector";
        label = "USB-C";
        power-role = "dual";
        try-power-role = "sink";
        source-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)>;
        sink-pdos = <PDO_FIXED(5000, 2000, PDO_FIXED_USB_COMM)
                     PDO_VAR(5000, 12000, 2000)>;
        op-sink-microwatt = <10000000>;
      };
    };

  # USB-C connector attached to SoC and USB3 typec port controller(hd3ss3220)
  # with SS 2:1 MUX. HS lines routed to SoC, SS lines routed to the MUX and
  # the output of MUX is connected to the SoC.
  - |
    connector {
        compatible = "usb-c-connector";
        label = "USB-C";
        data-role = "dual";

        ports {
                #address-cells = <1>;
                #size-cells = <0>;
                port@0 {
                        reg = <0>;
                        hs_ep: endpoint {
                                remote-endpoint = <&usb3_hs_ep>;
                        };
                };
                port@1 {
                        reg = <1>;
                        ss_ep: endpoint {
                                remote-endpoint = <&hd3ss3220_in_ep>;
                        };
                };
        };
    };

  # USB connector with GPIO control lines
  - |
    #include <dt-bindings/gpio/gpio.h>

    usb {
      connector {
        compatible = "gpio-usb-b-connector", "usb-b-connector";
        type = "micro";
        id-gpios = <&pio 12 GPIO_ACTIVE_HIGH>;
        vbus-supply = <&usb_p0_vbus>;
      };
    };

  # Micro-USB connector with HS lines routed via controller (MUIC) and MHL
  # lines connected to HDMI-MHL bridge (sii8620) on Samsung Exynos5433-based
  # mobile phone
  - |
    muic-max77843 {
      usb_con4: connector {
        compatible = "samsung,usb-connector-11pin", "usb-b-connector";
        label = "micro-USB";
        type = "micro";

        ports {
          #address-cells = <1>;
          #size-cells = <0>;

          port@0 {
            reg = <0>;
            muic_to_usb: endpoint {
              remote-endpoint = <&usb_to_muic>;
            };
          };
          port@3 {
            reg = <3>;
            usb_con_mhl: endpoint {
              remote-endpoint = <&sii8620_mhl>;
            };
          };
        };
      };
    };