| // SPDX-License-Identifier: GPL-2.0-only |
| |
| #include "msm8916.dtsi" |
| #include "pm8916.dtsi" |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| |
| / { |
| aliases { |
| serial0 = &blsp1_uart2; |
| }; |
| |
| chosen { |
| stdout-path = "serial0"; |
| }; |
| |
| soc { |
| sdhci@7824000 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8916_l8>; |
| vqmmc-supply = <&pm8916_l5>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>; |
| pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>; |
| }; |
| |
| sdhci@7864000 { |
| status = "okay"; |
| |
| vmmc-supply = <&pm8916_l11>; |
| vqmmc-supply = <&pm8916_l12>; |
| |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; |
| |
| cd-gpios = <&msmgpio 38 GPIO_ACTIVE_LOW>; |
| }; |
| |
| serial@78b0000 { |
| status = "okay"; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&blsp1_uart2_default>; |
| pinctrl-1 = <&blsp1_uart2_sleep>; |
| }; |
| |
| usb@78d9000 { |
| status = "okay"; |
| extcon = <&muic>, <&muic>; |
| |
| hnp-disable; |
| srp-disable; |
| adp-disable; |
| |
| ulpi { |
| phy { |
| extcon = <&muic>; |
| v1p8-supply = <&pm8916_l7>; |
| v3p3-supply = <&pm8916_l13>; |
| }; |
| }; |
| }; |
| |
| wcnss@a21b000 { |
| status = "okay"; |
| }; |
| |
| /* |
| * Attempting to enable these devices causes a "synchronous |
| * external abort". Suspected cause is that the debug power |
| * domain is not enabled by default on this device. |
| * Disable these devices for now to avoid the crash. |
| * |
| * See: https://lore.kernel.org/linux-arm-msm/20190618202623.GA53651@gerhold.net/ |
| */ |
| tpiu@820000 { status = "disabled"; }; |
| funnel@821000 { status = "disabled"; }; |
| replicator@824000 { status = "disabled"; }; |
| etf@825000 { status = "disabled"; }; |
| etr@826000 { status = "disabled"; }; |
| funnel@841000 { status = "disabled"; }; |
| debug@850000 { status = "disabled"; }; |
| debug@852000 { status = "disabled"; }; |
| debug@854000 { status = "disabled"; }; |
| debug@856000 { status = "disabled"; }; |
| etm@85c000 { status = "disabled"; }; |
| etm@85d000 { status = "disabled"; }; |
| etm@85e000 { status = "disabled"; }; |
| etm@85f000 { status = "disabled"; }; |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_keys_default>; |
| |
| label = "GPIO Buttons"; |
| |
| volume-up { |
| label = "Volume Up"; |
| gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_VOLUMEUP>; |
| }; |
| |
| home { |
| label = "Home"; |
| gpios = <&msmgpio 109 GPIO_ACTIVE_LOW>; |
| linux,code = <KEY_HOMEPAGE>; |
| }; |
| }; |
| |
| gpio-hall-sensor { |
| compatible = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&gpio_hall_sensor_default>; |
| |
| label = "GPIO Hall Effect Sensor"; |
| |
| hall-sensor { |
| label = "Hall Effect Sensor"; |
| gpios = <&msmgpio 52 GPIO_ACTIVE_LOW>; |
| linux,input-type = <EV_SW>; |
| linux,code = <SW_LID>; |
| linux,can-disable; |
| }; |
| }; |
| |
| i2c-muic { |
| compatible = "i2c-gpio"; |
| sda-gpios = <&msmgpio 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| scl-gpios = <&msmgpio 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| muic: sm5502@25 { |
| compatible = "siliconmitus,sm5502-muic"; |
| |
| reg = <0x25>; |
| interrupt-parent = <&msmgpio>; |
| interrupts = <12 IRQ_TYPE_EDGE_FALLING>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&muic_int_default>; |
| }; |
| }; |
| }; |
| |
| &msmgpio { |
| gpio_keys_default: gpio_keys_default { |
| pinmux { |
| function = "gpio"; |
| pins = "gpio107", "gpio109"; |
| }; |
| pinconf { |
| pins = "gpio107", "gpio109"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| }; |
| |
| gpio_hall_sensor_default: gpio_hall_sensor_default { |
| pinmux { |
| function = "gpio"; |
| pins = "gpio52"; |
| }; |
| pinconf { |
| pins = "gpio52"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| |
| muic_int_default: muic_int_default { |
| pinmux { |
| function = "gpio"; |
| pins = "gpio12"; |
| }; |
| pinconf { |
| pins = "gpio12"; |
| drive-strength = <2>; |
| bias-disable; |
| }; |
| }; |
| }; |
| |
| &smd_rpm_regulators { |
| vdd_l1_l2_l3-supply = <&pm8916_s3>; |
| vdd_l4_l5_l6-supply = <&pm8916_s4>; |
| vdd_l7-supply = <&pm8916_s4>; |
| |
| s1 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| s3 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1300000>; |
| }; |
| |
| s4 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2100000>; |
| }; |
| |
| l1 { |
| regulator-min-microvolt = <1225000>; |
| regulator-max-microvolt = <1225000>; |
| }; |
| |
| l2 { |
| regulator-min-microvolt = <1200000>; |
| regulator-max-microvolt = <1200000>; |
| }; |
| |
| l3 { |
| regulator-min-microvolt = <500000>; |
| regulator-max-microvolt = <1287500>; |
| }; |
| |
| l4 { |
| regulator-min-microvolt = <2050000>; |
| regulator-max-microvolt = <2050000>; |
| }; |
| |
| l5 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l6 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l7 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| }; |
| |
| l8 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2900000>; |
| }; |
| |
| l9 { |
| regulator-min-microvolt = <3300000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l10 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2800000>; |
| }; |
| |
| l11 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| regulator-allow-set-load; |
| regulator-system-load = <200000>; |
| }; |
| |
| l12 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <2950000>; |
| }; |
| |
| l13 { |
| regulator-min-microvolt = <3075000>; |
| regulator-max-microvolt = <3075000>; |
| }; |
| |
| l14 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l15 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l16 { |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <3300000>; |
| }; |
| |
| l17 { |
| regulator-min-microvolt = <2850000>; |
| regulator-max-microvolt = <2850000>; |
| }; |
| |
| l18 { |
| regulator-min-microvolt = <2700000>; |
| regulator-max-microvolt = <2700000>; |
| }; |
| }; |
| |
| &spmi_bus { |
| pm8916@0 { |
| pon@800 { |
| volume-down { |
| compatible = "qcom,pm8941-resin"; |
| interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>; |
| bias-pull-up; |
| linux,code = <KEY_VOLUMEDOWN>; |
| }; |
| }; |
| }; |
| }; |
