blob: c00797bd3b0777ff93319a18dc1de0af1758975a [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2019, Linaro Ltd.
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
#include <dt-bindings/sound/qcom,q6afe.h>
#include <dt-bindings/sound/qcom,q6asm.h>
#include "sdm845.dtsi"
#include "pm8998.dtsi"
#include "pmi8998.dtsi"
/ {
model = "Thundercomm Dragonboard 845c";
compatible = "thundercomm,db845c", "qcom,sdm845";
aliases {
serial0 = &uart9;
hsuart0 = &uart6;
};
chosen {
stdout-path = "serial0:115200n8";
};
dc12v: dc12v-regulator {
compatible = "regulator-fixed";
regulator-name = "DC12V";
regulator-min-microvolt = <12000000>;
regulator-max-microvolt = <12000000>;
regulator-always-on;
};
gpio_keys {
compatible = "gpio-keys";
autorepeat;
pinctrl-names = "default";
pinctrl-0 = <&vol_up_pin_a>;
vol-up {
label = "Volume Up";
linux,code = <KEY_VOLUMEUP>;
gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
};
};
leds {
compatible = "gpio-leds";
user4 {
label = "green:user4";
gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "panic-indicator";
default-state = "off";
};
wlan {
label = "yellow:wlan";
gpios = <&pm8998_gpio 9 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "phy0tx";
default-state = "off";
};
bt {
label = "blue:bt";
gpios = <&pm8998_gpio 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "bluetooth-power";
default-state = "off";
};
};
lt9611_1v8: lt9611-vdd18-regulator {
compatible = "regulator-fixed";
regulator-name = "LT9611_1V8";
vin-supply = <&vdc_5v>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
lt9611_3v3: lt9611-3v3 {
compatible = "regulator-fixed";
regulator-name = "LT9611_3V3";
vin-supply = <&vdc_3v3>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
pcie0_1p05v: pcie-0-1p05v-regulator {
compatible = "regulator-fixed";
regulator-name = "PCIE0_1.05V";
vin-supply = <&vbat>;
regulator-min-microvolt = <1050000>;
regulator-max-microvolt = <1050000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
cam0_dvdd_1v2: reg_cam0_dvdd_1v2 {
compatible = "regulator-fixed";
regulator-name = "CAM0_DVDD_1V2";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
enable-active-high;
gpio = <&pm8998_gpio 12 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&cam0_dvdd_1v2_en_default>;
vin-supply = <&vbat>;
};
cam0_avdd_2v8: reg_cam0_avdd_2v8 {
compatible = "regulator-fixed";
regulator-name = "CAM0_AVDD_2V8";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
enable-active-high;
gpio = <&pm8998_gpio 10 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&cam0_avdd_2v8_en_default>;
vin-supply = <&vbat>;
};
/* This regulator is enabled when the VREG_LVS1A_1P8 trace is enabled */
cam3_avdd_2v8: reg_cam3_avdd_2v8 {
compatible = "regulator-fixed";
regulator-name = "CAM3_AVDD_2V8";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-always-on;
vin-supply = <&vbat>;
};
pcie0_3p3v_dual: vldo-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "VLDO_3V3";
vin-supply = <&vbat>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&tlmm 90 GPIO_ACTIVE_HIGH>;
enable-active-high;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_pwren_state>;
};
v5p0_hdmiout: v5p0-hdmiout-regulator {
compatible = "regulator-fixed";
regulator-name = "V5P0_HDMIOUT";
vin-supply = <&vdc_5v>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <500000>;
// TODO: make it possible to drive same GPIO from two clients
// gpio = <&tlmm 89 GPIO_ACTIVE_HIGH>;
// enable-active-high;
};
vbat: vbat-regulator {
compatible = "regulator-fixed";
regulator-name = "VBAT";
vin-supply = <&dc12v>;
regulator-min-microvolt = <4200000>;
regulator-max-microvolt = <4200000>;
regulator-always-on;
};
vbat_som: vbat-som-regulator {
compatible = "regulator-fixed";
regulator-name = "VBAT_SOM";
vin-supply = <&dc12v>;
regulator-min-microvolt = <4200000>;
regulator-max-microvolt = <4200000>;
regulator-always-on;
};
vdc_3v3: vdc-3v3-regulator {
compatible = "regulator-fixed";
regulator-name = "VDC_3V3";
vin-supply = <&dc12v>;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
vdc_5v: vdc-5v-regulator {
compatible = "regulator-fixed";
regulator-name = "VDC_5V";
vin-supply = <&dc12v>;
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <500000>;
regulator-always-on;
};
vreg_s4a_1p8: vreg-s4a-1p8 {
compatible = "regulator-fixed";
regulator-name = "vreg_s4a_1p8";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
vin-supply = <&vbat_som>;
};
};
&adsp_pas {
status = "okay";
firmware-name = "qcom/sdm845/adsp.mdt";
};
&apps_rsc {
pm8998-rpmh-regulators {
compatible = "qcom,pm8998-rpmh-regulators";
qcom,pmic-id = "a";
vdd-s1-supply = <&vph_pwr>;
vdd-s2-supply = <&vph_pwr>;
vdd-s3-supply = <&vph_pwr>;
vdd-s4-supply = <&vph_pwr>;
vdd-s5-supply = <&vph_pwr>;
vdd-s6-supply = <&vph_pwr>;
vdd-s7-supply = <&vph_pwr>;
vdd-s8-supply = <&vph_pwr>;
vdd-s9-supply = <&vph_pwr>;
vdd-s10-supply = <&vph_pwr>;
vdd-s11-supply = <&vph_pwr>;
vdd-s12-supply = <&vph_pwr>;
vdd-s13-supply = <&vph_pwr>;
vdd-l1-l27-supply = <&vreg_s7a_1p025>;
vdd-l2-l8-l17-supply = <&vreg_s3a_1p35>;
vdd-l3-l11-supply = <&vreg_s7a_1p025>;
vdd-l4-l5-supply = <&vreg_s7a_1p025>;
vdd-l6-supply = <&vph_pwr>;
vdd-l7-l12-l14-l15-supply = <&vreg_s5a_2p04>;
vdd-l9-supply = <&vreg_bob>;
vdd-l10-l23-l25-supply = <&vreg_bob>;
vdd-l13-l19-l21-supply = <&vreg_bob>;
vdd-l16-l28-supply = <&vreg_bob>;
vdd-l18-l22-supply = <&vreg_bob>;
vdd-l20-l24-supply = <&vreg_bob>;
vdd-l26-supply = <&vreg_s3a_1p35>;
vin-lvs-1-2-supply = <&vreg_s4a_1p8>;
vreg_s3a_1p35: smps3 {
regulator-min-microvolt = <1352000>;
regulator-max-microvolt = <1352000>;
};
vreg_s5a_2p04: smps5 {
regulator-min-microvolt = <1904000>;
regulator-max-microvolt = <2040000>;
};
vreg_s7a_1p025: smps7 {
regulator-min-microvolt = <900000>;
regulator-max-microvolt = <1028000>;
};
vreg_l1a_0p875: ldo1 {
regulator-min-microvolt = <880000>;
regulator-max-microvolt = <880000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l5a_0p8: ldo5 {
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l12a_1p8: ldo12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l7a_1p8: ldo7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l13a_2p95: ldo13 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2960000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l17a_1p3: ldo17 {
regulator-min-microvolt = <1304000>;
regulator-max-microvolt = <1304000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l20a_2p95: ldo20 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2968000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l21a_2p95: ldo21 {
regulator-min-microvolt = <2960000>;
regulator-max-microvolt = <2968000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l24a_3p075: ldo24 {
regulator-min-microvolt = <3088000>;
regulator-max-microvolt = <3088000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l25a_3p3: ldo25 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3312000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_l26a_1p2: ldo26 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
};
vreg_lvs1a_1p8: lvs1 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
vreg_lvs2a_1p8: lvs2 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
};
};
pmi8998-rpmh-regulators {
compatible = "qcom,pmi8998-rpmh-regulators";
qcom,pmic-id = "b";
vdd-bob-supply = <&vph_pwr>;
vreg_bob: bob {
regulator-min-microvolt = <3312000>;
regulator-max-microvolt = <3600000>;
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
regulator-allow-bypass;
};
};
};
&cdsp_pas {
status = "okay";
firmware-name = "qcom/sdm845/cdsp.mdt";
};
&gcc {
protected-clocks = <GCC_QSPI_CORE_CLK>,
<GCC_QSPI_CORE_CLK_SRC>,
<GCC_QSPI_CNOC_PERIPH_AHB_CLK>;
};
&gpu {
zap-shader {
memory-region = <&gpu_mem>;
firmware-name = "qcom/sdm845/a630_zap.mbn";
};
};
&i2c11 {
/* On Low speed expansion */
label = "LS-I2C1";
status = "okay";
};
&i2c14 {
/* On Low speed expansion */
label = "LS-I2C0";
status = "okay";
};
&mss_pil {
status = "okay";
firmware-name = "qcom/sdm845/mba.mbn", "qcom/sdm845/modem.mbn";
};
&pcie0 {
status = "okay";
perst-gpio = <&tlmm 35 GPIO_ACTIVE_LOW>;
enable-gpio = <&tlmm 134 GPIO_ACTIVE_HIGH>;
vddpe-3v3-supply = <&pcie0_3p3v_dual>;
pinctrl-names = "default";
pinctrl-0 = <&pcie0_default_state>;
};
&pcie0_phy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l26a_1p2>;
};
&pcie1 {
status = "okay";
perst-gpio = <&tlmm 102 GPIO_ACTIVE_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&pcie1_default_state>;
};
&pcie1_phy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l26a_1p2>;
};
&pm8998_gpio {
gpio-line-names =
"NC",
"NC",
"WLAN_SW_CTRL",
"NC",
"PM_GPIO5_BLUE_BT_LED",
"VOL_UP_N",
"NC",
"ADC_IN1",
"PM_GPIO9_YEL_WIFI_LED",
"CAM0_AVDD_EN",
"NC",
"CAM0_DVDD_EN",
"PM_GPIO13_GREEN_U4_LED",
"DIV_CLK2",
"NC",
"NC",
"NC",
"SMB_STAT",
"NC",
"NC",
"ADC_IN2",
"OPTION1",
"WCSS_PWR_REQ",
"PM845_GPIO24",
"OPTION2",
"PM845_SLB";
cam0_dvdd_1v2_en_default: cam0-dvdd-1v2-en {
pins = "gpio12";
function = "normal";
bias-pull-up;
drive-push-pull;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
};
cam0_avdd_2v8_en_default: cam0-avdd-2v8-en {
pins = "gpio10";
function = "normal";
bias-pull-up;
drive-push-pull;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
};
vol_up_pin_a: vol-up-active {
pins = "gpio6";
function = "normal";
input-enable;
bias-pull-up;
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
};
};
&pm8998_pon {
resin {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
debounce = <15625>;
bias-pull-up;
linux,code = <KEY_VOLUMEDOWN>;
};
};
/* QUAT I2S Uses 4 I2S SD Lines for audio on LT9611 HDMI Bridge */
&q6afedai {
qi2s@22 {
reg = <22>;
qcom,sd-lines = <0 1 2 3>;
};
};
&q6asmdai {
dai@0 {
reg = <0>;
};
dai@1 {
reg = <1>;
};
dai@2 {
reg = <2>;
};
dai@3 {
reg = <3>;
direction = <2>;
is-compress-dai;
};
};
&qupv3_id_0 {
status = "okay";
};
&qupv3_id_1 {
status = "okay";
};
&sdhc_2 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
vmmc-supply = <&vreg_l21a_2p95>;
vqmmc-supply = <&vreg_l13a_2p95>;
bus-width = <4>;
cd-gpios = <&tlmm 126 GPIO_ACTIVE_LOW>;
};
&sound {
compatible = "qcom,db845c-sndcard";
pinctrl-0 = <&quat_mi2s_active
&quat_mi2s_sd0_active
&quat_mi2s_sd1_active
&quat_mi2s_sd2_active
&quat_mi2s_sd3_active>;
pinctrl-names = "default";
model = "DB845c";
audio-routing =
"RX_BIAS", "MCLK",
"AMIC1", "MIC BIAS1",
"AMIC2", "MIC BIAS2",
"DMIC0", "MIC BIAS1",
"DMIC1", "MIC BIAS1",
"DMIC2", "MIC BIAS3",
"DMIC3", "MIC BIAS3",
"SpkrLeft IN", "SPK1 OUT",
"SpkrRight IN", "SPK2 OUT",
"MM_DL1", "MultiMedia1 Playback",
"MM_DL2", "MultiMedia2 Playback",
"MM_DL4", "MultiMedia4 Playback",
"MultiMedia3 Capture", "MM_UL3";
mm1-dai-link {
link-name = "MultiMedia1";
cpu {
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
};
};
mm2-dai-link {
link-name = "MultiMedia2";
cpu {
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
};
};
mm3-dai-link {
link-name = "MultiMedia3";
cpu {
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
};
};
mm4-dai-link {
link-name = "MultiMedia4";
cpu {
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA4>;
};
};
slim-dai-link {
link-name = "SLIM Playback";
cpu {
sound-dai = <&q6afedai SLIMBUS_0_RX>;
};
platform {
sound-dai = <&q6routing>;
};
codec {
sound-dai = <&left_spkr>, <&right_spkr>, <&swm 0>, <&wcd9340 0>;
};
};
slimcap-dai-link {
link-name = "SLIM Capture";
cpu {
sound-dai = <&q6afedai SLIMBUS_0_TX>;
};
platform {
sound-dai = <&q6routing>;
};
codec {
sound-dai = <&wcd9340 1>;
};
};
};
&spi2 {
/* On Low speed expansion */
label = "LS-SPI0";
status = "okay";
};
&tlmm {
cam0_default: cam0_default {
rst {
pins = "gpio9";
function = "gpio";
drive-strength = <16>;
bias-disable;
};
mclk0 {
pins = "gpio13";
function = "cam_mclk";
drive-strength = <16>;
bias-disable;
};
};
cam3_default: cam3_default {
rst {
function = "gpio";
pins = "gpio21";
drive-strength = <16>;
bias-disable;
};
mclk3 {
function = "cam_mclk";
pins = "gpio16";
drive-strength = <16>;
bias-disable;
};
};
pcie0_default_state: pcie0-default {
clkreq {
pins = "gpio36";
function = "pci_e0";
bias-pull-up;
};
reset-n {
pins = "gpio35";
function = "gpio";
drive-strength = <2>;
output-low;
bias-pull-down;
};
wake-n {
pins = "gpio37";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
};
pcie0_pwren_state: pcie0-pwren {
pins = "gpio90";
function = "gpio";
drive-strength = <2>;
bias-disable;
};
pcie1_default_state: pcie1-default {
perst-n {
pins = "gpio102";
function = "gpio";
drive-strength = <16>;
bias-disable;
};
clkreq {
pins = "gpio103";
function = "pci_e1";
bias-pull-up;
};
wake-n {
pins = "gpio11";
function = "gpio";
drive-strength = <2>;
bias-pull-up;
};
reset-n {
pins = "gpio75";
function = "gpio";
drive-strength = <16>;
bias-pull-up;
output-high;
};
};
sdc2_default_state: sdc2-default {
clk {
pins = "sdc2_clk";
bias-disable;
/*
* It seems that mmc_test reports errors if drive
* strength is not 16 on clk, cmd, and data pins.
*/
drive-strength = <16>;
};
cmd {
pins = "sdc2_cmd";
bias-pull-up;
drive-strength = <10>;
};
data {
pins = "sdc2_data";
bias-pull-up;
drive-strength = <10>;
};
};
sdc2_card_det_n: sd-card-det-n {
pins = "gpio126";
function = "gpio";
bias-pull-up;
};
wcd_intr_default: wcd_intr_default {
pins = <54>;
function = "gpio";
input-enable;
bias-pull-down;
drive-strength = <2>;
};
};
&uart3 {
label = "LS-UART0";
status = "disabled";
};
&uart6 {
status = "okay";
bluetooth {
compatible = "qcom,wcn3990-bt";
vddio-supply = <&vreg_s4a_1p8>;
vddxo-supply = <&vreg_l7a_1p8>;
vddrf-supply = <&vreg_l17a_1p3>;
vddch0-supply = <&vreg_l25a_3p3>;
max-speed = <3200000>;
};
};
&uart9 {
label = "LS-UART1";
status = "okay";
};
&usb_1 {
status = "okay";
};
&usb_1_dwc3 {
dr_mode = "peripheral";
};
&usb_1_hsphy {
status = "okay";
vdd-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
};
&usb_1_qmpphy {
status = "okay";
vdda-phy-supply = <&vreg_l26a_1p2>;
vdda-pll-supply = <&vreg_l1a_0p875>;
};
&usb_2 {
status = "okay";
};
&usb_2_dwc3 {
dr_mode = "host";
};
&usb_2_hsphy {
status = "okay";
vdd-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l12a_1p8>;
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
qcom,imp-res-offset-value = <8>;
qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_22_8_MA>;
};
&usb_2_qmpphy {
status = "okay";
vdda-phy-supply = <&vreg_l26a_1p2>;
vdda-pll-supply = <&vreg_l1a_0p875>;
};
&ufs_mem_hc {
status = "okay";
reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
vcc-supply = <&vreg_l20a_2p95>;
vcc-max-microamp = <800000>;
};
&ufs_mem_phy {
status = "okay";
vdda-phy-supply = <&vreg_l1a_0p875>;
vdda-pll-supply = <&vreg_l26a_1p2>;
};
&wcd9340{
pinctrl-0 = <&wcd_intr_default>;
pinctrl-names = "default";
clock-names = "extclk";
clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
reset-gpios = <&tlmm 64 0>;
vdd-buck-supply = <&vreg_s4a_1p8>;
vdd-buck-sido-supply = <&vreg_s4a_1p8>;
vdd-tx-supply = <&vreg_s4a_1p8>;
vdd-rx-supply = <&vreg_s4a_1p8>;
vdd-io-supply = <&vreg_s4a_1p8>;
swm: swm@c85 {
left_spkr: wsa8810-left{
compatible = "sdw10217201000";
reg = <0 1>;
powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
#thermal-sensor-cells = <0>;
sound-name-prefix = "SpkrLeft";
#sound-dai-cells = <0>;
};
right_spkr: wsa8810-right{
compatible = "sdw10217201000";
powerdown-gpios = <&wcdgpio 2 GPIO_ACTIVE_HIGH>;
reg = <0 2>;
#thermal-sensor-cells = <0>;
sound-name-prefix = "SpkrRight";
#sound-dai-cells = <0>;
};
};
};
&wifi {
status = "okay";
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
qcom,snoc-host-cap-8bit-quirk;
};
/* PINCTRL - additions to nodes defined in sdm845.dtsi */
&qup_spi2_default {
drive-strength = <16>;
};
&qup_uart3_default{
pinmux {
pins = "gpio41", "gpio42", "gpio43", "gpio44";
function = "qup3";
};
};
&qup_uart6_default {
pinmux {
pins = "gpio45", "gpio46", "gpio47", "gpio48";
function = "qup6";
};
cts {
pins = "gpio45";
bias-disable;
};
rts-tx {
pins = "gpio46", "gpio47";
drive-strength = <2>;
bias-disable;
};
rx {
pins = "gpio48";
bias-pull-up;
};
};
&qup_uart9_default {
pinconf-tx {
pins = "gpio4";
drive-strength = <2>;
bias-disable;
};
pinconf-rx {
pins = "gpio5";
drive-strength = <2>;
bias-pull-up;
};
};
&pm8998_gpio {
};
&cci {
status = "ok";
};
&cci_i2c0 {
camera@10 {
compatible = "ovti,ov8856";
reg = <0x10>;
// CAM0_RST_N
reset-gpios = <&tlmm 9 0>;
pinctrl-names = "default";
pinctrl-0 = <&cam0_default>;
gpios = <&tlmm 13 0>,
<&tlmm 9 0>;
clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
clock-names = "xvclk";
clock-frequency = <19200000>;
/* The &vreg_s4a_1p8 trace is powered on as a,
* so it is represented by a fixed regulator.
*
* The 2.8V vdda-supply and 1.2V vddd-supply regulators
* both have to be enabled through the power management
* gpios.
*/
power-domains = <&clock_camcc TITAN_TOP_GDSC>;
dovdd-supply = <&vreg_lvs1a_1p8>;
avdd-supply = <&cam0_avdd_2v8>;
dvdd-supply = <&cam0_dvdd_1v2>;
status = "disable";
port {
ov8856_ep: endpoint {
clock-lanes = <1>;
link-frequencies = /bits/ 64
<360000000 180000000>;
data-lanes = <1 2 3 4>;
// remote-endpoint = <&csiphy0_ep>;
};
};
};
};
&cci_i2c1 {
camera@60 {
compatible = "ovti,ov7251";
// I2C address as per ov7251.txt linux documentation
reg = <0x60>;
// CAM3_RST_N
enable-gpios = <&tlmm 21 0>;
pinctrl-names = "default";
pinctrl-0 = <&cam3_default>;
gpios = <&tlmm 16 0>,
<&tlmm 21 0>;
clocks = <&clock_camcc CAM_CC_MCLK3_CLK>;
clock-names = "xclk";
clock-frequency = <24000000>;
/* The &vreg_s4a_1p8 trace always powered on.
*
* The 2.8V vdda-supply regulator is enabled when the
* vreg_s4a_1p8 trace is pulled high.
* It too is represented by a fixed regulator.
*
* No 1.2V vddd-supply regulator is used.
*/
power-domains = <&clock_camcc TITAN_TOP_GDSC>;
vdddo-supply = <&vreg_lvs1a_1p8>;
vdda-supply = <&cam3_avdd_2v8>;
status = "disable";
port {
ov7251_ep: endpoint {
clock-lanes = <1>;
data-lanes = <0 1>;
// remote-endpoint = <&csiphy3_ep>;
};
};
};
};