blob: 151be3bba06f178d3e86390a57f21c80fc6bc7e1 [file] [log] [blame]
Rockchip specific extensions to the Synopsys Designware MIPI DSI
================================
Required properties:
- #address-cells: Should be <1>.
- #size-cells: Should be <0>.
- compatible: one of
"rockchip,px30-mipi-dsi", "snps,dw-mipi-dsi"
"rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi"
"rockchip,rk3399-mipi-dsi", "snps,dw-mipi-dsi"
- reg: Represent the physical address range of the controller.
- interrupts: Represent the controller's interrupt to the CPU(s).
- clocks, clock-names: Phandles to the controller's pll reference
clock(ref) when using an internal dphy and APB clock(pclk).
For RK3399, a phy config clock (phy_cfg) and a grf clock(grf)
are required. As described in [1].
- rockchip,grf: this soc should set GRF regs to mux vopl/vopb.
- ports: contain a port node with endpoint definitions as defined in [2].
For vopb,set the reg = <0> and set the reg = <1> for vopl.
- video port 0 for the VOP input, the remote endpoint maybe vopb or vopl
- video port 1 for either a panel or subsequent encoder
Optional properties:
- phys: from general PHY binding: the phandle for the PHY device.
- phy-names: Should be "dphy" if phys references an external phy.
- power-domains: a phandle to mipi dsi power domain node.
- resets: list of phandle + reset specifier pairs, as described in [3].
- reset-names: string reset name, must be "apb".
[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
[2] Documentation/devicetree/bindings/media/video-interfaces.txt
[3] Documentation/devicetree/bindings/reset/reset.txt
Example:
mipi_dsi: mipi@ff960000 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "rockchip,rk3288-mipi-dsi", "snps,dw-mipi-dsi";
reg = <0xff960000 0x4000>;
interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cru SCLK_MIPI_24M>, <&cru PCLK_MIPI_DSI0>;
clock-names = "ref", "pclk";
resets = <&cru SRST_MIPIDSI0>;
reset-names = "apb";
rockchip,grf = <&grf>;
ports {
#address-cells = <1>;
#size-cells = <0>;
mipi_in: port@0 {
reg = <0>;
#address-cells = <1>;
#size-cells = <0>;
mipi_in_vopb: endpoint@0 {
reg = <0>;
remote-endpoint = <&vopb_out_mipi>;
};
mipi_in_vopl: endpoint@1 {
reg = <1>;
remote-endpoint = <&vopl_out_mipi>;
};
};
mipi_out: port@1 {
reg = <1>;
#address-cells = <1>;
#size-cells = <0>;
mipi_out_panel: endpoint {
remote-endpoint = <&panel_in_mipi>;
};
};
};
panel {
compatible ="boe,tv080wum-nl0";
reg = <0>;
enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&lcd_en>;
backlight = <&backlight>;
port {
panel_in_mipi: endpoint {
remote-endpoint = <&mipi_out_panel>;
};
};
};
};