blob: 7e5e427a22ce2473d2b3912598da368a3a0bf720 [file] [log] [blame]
* Synopsys Designware Mobile Storage Host Controller
The Synopsys designware mobile storage host controller is used to interface
a SoC with storage medium such as eMMC or SD/MMC cards. This file documents
differences between the core mmc properties described by mmc.txt and the
properties used by the Synopsys Designware Mobile Storage Host Controller.
Required Properties:
* compatible: should be
- snps,dw-mshc: for controllers compliant with synopsys dw-mshc.
* #address-cells: should be 1.
* #size-cells: should be 0.
# Slots (DEPRECATED): The slot specific information are contained within
child-nodes with each child-node representing a supported slot. There should
be atleast one child node representing a card slot. The name of the child node
representing the slot is recommended to be slot@n where n is the unique number
of the slot connected to the controller. The following are optional properties
which can be included in the slot child node.
* reg: specifies the physical slot number. The valid values of this
property is 0 to (num-slots -1), where num-slots is the value
specified by the num-slots property.
* bus-width: as documented in mmc core bindings.
* wp-gpios: specifies the write protect gpio line. The format of the
gpio specifier depends on the gpio controller. If a GPIO is not used
for write-protect, this property is optional.
* disable-wp: If the wp-gpios property isn't present then (by default)
we'd assume that the write protect is hooked up directly to the
controller's special purpose write protect line (accessible via
the WRTPRT register). However, it's possible that we simply don't
want write protect. In that case specify 'disable-wp'.
NOTE: This property is not required for slots known to always
connect to eMMC or SDIO cards.
Optional properties:
* resets: phandle + reset specifier pair, intended to represent hardware
reset signal present internally in some host controller IC designs.
See Documentation/devicetree/bindings/reset/reset.txt for details.
* reset-names: request name for using "resets" property. Must be "reset".
(It will be used together with "resets" property.)
* clocks: from common clock binding: handle to biu and ciu clocks for the
bus interface unit clock and the card interface unit clock.
* clock-names: from common clock binding: Shall be "biu" and "ciu".
If the biu clock is missing we'll simply skip enabling it. If the
ciu clock is missing we'll just assume that the clock is running at
clock-frequency. It is an error to omit both the ciu clock and the
* clock-frequency: should be the frequency (in Hz) of the ciu clock. If this
is specified and the ciu clock is specified then we'll try to set the ciu
clock to this at probe time.
* fifo-depth: The maximum size of the tx/rx fifo's. If this property is not
specified, the default value of the fifo size is determined from the
controller registers.
* card-detect-delay: Delay in milli-seconds before detecting card after card
insert event. The default value is 0.
* data-addr: Override fifo address with value provided by DT. The default FIFO reg
offset is assumed as 0x100 (version < 0x240A) and 0x200(version >= 0x240A) by
driver. If the controller does not follow this rule, please use this property
to set fifo address in device tree.
* fifo-watermark-aligned: Data done irq is expected if data length is less than
watermark in PIO mode. But fifo watermark is requested to be aligned with data
length in some SoC so that TX/RX irq can be generated with data done irq. Add this
watermark quirk to mark this requirement and force fifo watermark setting
* vmmc-supply: The phandle to the regulator to use for vmmc. If this is
specified we'll defer probe until we can find this regulator.
* dmas: List of DMA specifiers with the controller specific format as described
in the generic DMA client binding. Refer to dma.txt for details.
* dma-names: request names for generic DMA client binding. Must be "rx-tx".
Refer to dma.txt for details.
- All the MSHC controller nodes should be represented in the aliases node using
the following format 'mshc{n}' where n is a unique number for the alias.
The MSHC controller node can be split into two portions, SoC specific and
board specific portions as listed below.
dwmmc0@12200000 {
compatible = "snps,dw-mshc";
clocks = <&clock 351>, <&clock 132>;
clock-names = "biu", "ciu";
reg = <0x12200000 0x1000>;
interrupts = <0 75 0>;
#address-cells = <1>;
#size-cells = <0>;
data-addr = <0x200>;
resets = <&rst 20>;
reset-names = "reset";
[board specific internal DMA resources]
dwmmc0@12200000 {
clock-frequency = <400000000>;
clock-freq-min-max = <400000 200000000>;
fifo-depth = <0x80>;
card-detect-delay = <200>;
vmmc-supply = <&buck8>;
bus-width = <8>;
[board specific generic DMA request binding]
dwmmc0@12200000 {
clock-frequency = <400000000>;
clock-freq-min-max = <400000 200000000>;
fifo-depth = <0x80>;
card-detect-delay = <200>;
vmmc-supply = <&buck8>;
bus-width = <8>;
dmas = <&pdma 12>;
dma-names = "rx-tx";