blob: d5230cb76eb12d43e1d4077e970d42adb89f56bb [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0-only
/dts-v1/;
#include "msm8916.dtsi"
#include "pm8916.dtsi"
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
model = "Longcheer L8150";
compatible = "longcheer,l8150", "qcom,msm8916-v1-qrd/9-v1", "qcom,msm8916";
aliases {
serial0 = &blsp1_uart2;
};
chosen {
stdout-path = "serial0";
};
reserved-memory {
// wcnss.mdt is not relocatable, so it must be loaded at 0x8b600000
/delete-node/ wcnss@89300000;
wcnss_mem: wcnss@8b600000 {
reg = <0x0 0x8b600000 0x0 0x600000>;
no-map;
};
};
soc {
sdhci@7824000 {
status = "okay";
vmmc-supply = <&pm8916_l8>;
vqmmc-supply = <&pm8916_l5>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc1_clk_on &sdc1_cmd_on &sdc1_data_on>;
pinctrl-1 = <&sdc1_clk_off &sdc1_cmd_off &sdc1_data_off>;
};
sdhci@7864000 {
status = "okay";
vmmc-supply = <&pm8916_l11>;
vqmmc-supply = <&pm8916_l12>;
pinctrl-names = "default", "sleep";
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on>;
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off>;
non-removable;
};
serial@78b0000 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-0 = <&blsp1_uart2_default>;
pinctrl-1 = <&blsp1_uart2_sleep>;
};
usb@78d9000 {
status = "okay";
dr_mode = "peripheral";
extcon = <&usb_vbus>;
hnp-disable;
srp-disable;
adp-disable;
ulpi {
phy {
extcon = <&usb_vbus>;
v1p8-supply = <&pm8916_l7>;
v3p3-supply = <&pm8916_l13>;
};
};
};
wcnss@a21b000 {
status = "okay";
};
};
// FIXME: Use extcon device provided by charger driver when available
usb_vbus: usb-vbus {
compatible = "linux,extcon-usb-gpio";
vbus-gpio = <&msmgpio 62 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb_vbus_default>;
};
gpio-keys {
compatible = "gpio-keys";
pinctrl-names = "default";
pinctrl-0 = <&gpio_keys_default>;
label = "GPIO Buttons";
volume-up {
label = "Volume Up";
gpios = <&msmgpio 107 GPIO_ACTIVE_LOW>;
linux,code = <KEY_VOLUMEUP>;
};
};
};
&msmgpio {
gpio_keys_default: gpio-keys-default {
pinmux {
function = "gpio";
pins = "gpio107";
};
pinconf {
pins = "gpio107";
drive-strength = <2>;
bias-pull-up;
};
};
usb_vbus_default: usb-vbus-default {
pinmux {
function = "gpio";
pins = "gpio62";
};
pinconf {
pins = "gpio62";
bias-pull-up;
};
};
};
&spmi_bus {
pm8916@0 {
pon@800 {
volume-down {
compatible = "qcom,pm8941-resin";
interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
bias-pull-up;
linux,code = <KEY_VOLUMEDOWN>;
};
};
};
};
&smd_rpm_regulators {
vdd_l1_l2_l3-supply = <&pm8916_s3>;
vdd_l4_l5_l6-supply = <&pm8916_s4>;
vdd_l7-supply = <&pm8916_s4>;
s1 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1300000>;
};
s3 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1300000>;
};
s4 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2100000>;
};
l1 {
regulator-min-microvolt = <1225000>;
regulator-max-microvolt = <1225000>;
};
l2 {
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
};
l3 {
regulator-min-microvolt = <500000>;
regulator-max-microvolt = <1287500>;
};
l4 {
regulator-min-microvolt = <2050000>;
regulator-max-microvolt = <2050000>;
};
l5 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l6 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l7 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
};
l8 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2900000>;
};
l9 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
l10 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2800000>;
};
l11 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
regulator-allow-set-load;
regulator-system-load = <200000>;
};
l12 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <2950000>;
};
l13 {
regulator-min-microvolt = <3075000>;
regulator-max-microvolt = <3075000>;
};
l14 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l15 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l16 {
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3300000>;
};
l17 {
regulator-min-microvolt = <2850000>;
regulator-max-microvolt = <2850000>;
};
l18 {
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
};
};