Merge tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A collection of driver specific fixes, there was a bit of a kerfuffle
with some last minute review on hte spi-cadence-quadspi division by
zero change but otherwise nothing terribly remarkable here - important
fixes if you have the hardware but nothing with too wide an impact"
* tag 'spi-fix-v5.14-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-bcm2835: Fix deadlock
spi: cadence: Correct initialisation of runtime PM again
spi: cadence-quadspi: Disable Auto-HW polling
spi: spi-cadence-quadspi: Fix division by zero warning
spi: spi-cadence-quadspi: Revert "Fix division by zero warning"
spi: spi-cadence-quadspi: Fix division by zero warning
spi: mediatek: move devm_spi_register_master position
spi: mediatek: fix fifo rx mode
spi: atmel: Fix CS and initialization bug
spi: stm32: fixes pm_runtime calls in probe/remove
spi: imx: mx51-ecspi: Reinstate low-speed CONFIGREG delay
spi: stm32h7: fix full duplex irq handler handling
diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c
index 2ef7488..788dcdf 100644
--- a/drivers/spi/spi-atmel.c
+++ b/drivers/spi/spi-atmel.c
@@ -352,8 +352,6 @@
}
mr = spi_readl(as, MR);
- if (spi->cs_gpiod)
- gpiod_set_value(spi->cs_gpiod, 1);
} else {
u32 cpol = (spi->mode & SPI_CPOL) ? SPI_BIT(CPOL) : 0;
int i;
@@ -369,8 +367,6 @@
mr = spi_readl(as, MR);
mr = SPI_BFINS(PCS, ~(1 << chip_select), mr);
- if (spi->cs_gpiod)
- gpiod_set_value(spi->cs_gpiod, 1);
spi_writel(as, MR, mr);
}
@@ -400,8 +396,6 @@
if (!spi->cs_gpiod)
spi_writel(as, CR, SPI_BIT(LASTXFER));
- else
- gpiod_set_value(spi->cs_gpiod, 0);
}
static void atmel_spi_lock(struct atmel_spi *as) __acquires(&as->lock)
@@ -1483,7 +1477,8 @@
master->bus_num = pdev->id;
master->num_chipselect = 4;
master->setup = atmel_spi_setup;
- master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX);
+ master->flags = (SPI_MASTER_MUST_RX | SPI_MASTER_MUST_TX |
+ SPI_MASTER_GPIO_SS);
master->transfer_one = atmel_spi_one_transfer;
master->set_cs = atmel_spi_set_cs;
master->cleanup = atmel_spi_cleanup;
diff --git a/drivers/spi/spi-bcm2835.c b/drivers/spi/spi-bcm2835.c
index 5f8771f..775c0bf 100644
--- a/drivers/spi/spi-bcm2835.c
+++ b/drivers/spi/spi-bcm2835.c
@@ -83,6 +83,7 @@
* struct bcm2835_spi - BCM2835 SPI controller
* @regs: base address of register map
* @clk: core clock, divided to calculate serial clock
+ * @clk_hz: core clock cached speed
* @irq: interrupt, signals TX FIFO empty or RX FIFO ¾ full
* @tfr: SPI transfer currently processed
* @ctlr: SPI controller reverse lookup
@@ -116,6 +117,7 @@
struct bcm2835_spi {
void __iomem *regs;
struct clk *clk;
+ unsigned long clk_hz;
int irq;
struct spi_transfer *tfr;
struct spi_controller *ctlr;
@@ -1045,19 +1047,18 @@
{
struct bcm2835_spi *bs = spi_controller_get_devdata(ctlr);
struct bcm2835_spidev *slv = spi_get_ctldata(spi);
- unsigned long spi_hz, clk_hz, cdiv;
+ unsigned long spi_hz, cdiv;
unsigned long hz_per_byte, byte_limit;
u32 cs = slv->prepare_cs;
/* set clock */
spi_hz = tfr->speed_hz;
- clk_hz = clk_get_rate(bs->clk);
- if (spi_hz >= clk_hz / 2) {
+ if (spi_hz >= bs->clk_hz / 2) {
cdiv = 2; /* clk_hz/2 is the fastest we can go */
} else if (spi_hz) {
/* CDIV must be a multiple of two */
- cdiv = DIV_ROUND_UP(clk_hz, spi_hz);
+ cdiv = DIV_ROUND_UP(bs->clk_hz, spi_hz);
cdiv += (cdiv % 2);
if (cdiv >= 65536)
@@ -1065,7 +1066,7 @@
} else {
cdiv = 0; /* 0 is the slowest we can go */
}
- tfr->effective_speed_hz = cdiv ? (clk_hz / cdiv) : (clk_hz / 65536);
+ tfr->effective_speed_hz = cdiv ? (bs->clk_hz / cdiv) : (bs->clk_hz / 65536);
bcm2835_wr(bs, BCM2835_SPI_CLK, cdiv);
/* handle all the 3-wire mode */
@@ -1354,6 +1355,7 @@
return bs->irq ? bs->irq : -ENODEV;
clk_prepare_enable(bs->clk);
+ bs->clk_hz = clk_get_rate(bs->clk);
err = bcm2835_dma_init(ctlr, &pdev->dev, bs);
if (err)
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index 7a00346..a2de235 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -309,6 +309,9 @@
{
unsigned int dummy_clk;
+ if (!op->dummy.nbytes)
+ return 0;
+
dummy_clk = op->dummy.nbytes * (8 / op->dummy.buswidth);
if (dtr)
dummy_clk /= 2;
@@ -797,19 +800,20 @@
reg = cqspi_calc_rdreg(f_pdata);
writel(reg, reg_base + CQSPI_REG_RD_INSTR);
- if (f_pdata->dtr) {
- /*
- * Some flashes like the cypress Semper flash expect a 4-byte
- * dummy address with the Read SR command in DTR mode, but this
- * controller does not support sending address with the Read SR
- * command. So, disable write completion polling on the
- * controller's side. spi-nor will take care of polling the
- * status register.
- */
- reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
- reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
- writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
- }
+ /*
+ * SPI NAND flashes require the address of the status register to be
+ * passed in the Read SR command. Also, some SPI NOR flashes like the
+ * cypress Semper flash expect a 4-byte dummy address in the Read SR
+ * command in DTR mode.
+ *
+ * But this controller does not support address phase in the Read SR
+ * command when doing auto-HW polling. So, disable write completion
+ * polling on the controller's side. spinand and spi-nor will take
+ * care of polling the status register.
+ */
+ reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+ reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
+ writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
reg = readl(reg_base + CQSPI_REG_SIZE);
reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
diff --git a/drivers/spi/spi-cadence.c b/drivers/spi/spi-cadence.c
index a3afd1b..ceb16e7 100644
--- a/drivers/spi/spi-cadence.c
+++ b/drivers/spi/spi-cadence.c
@@ -517,6 +517,12 @@
goto clk_dis_apb;
}
+ pm_runtime_use_autosuspend(&pdev->dev);
+ pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
+ pm_runtime_get_noresume(&pdev->dev);
+ pm_runtime_set_active(&pdev->dev);
+ pm_runtime_enable(&pdev->dev);
+
ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
if (ret < 0)
master->num_chipselect = CDNS_SPI_DEFAULT_NUM_CS;
@@ -531,11 +537,6 @@
/* SPI controller initializations */
cdns_spi_init_hw(xspi);
- pm_runtime_set_active(&pdev->dev);
- pm_runtime_enable(&pdev->dev);
- pm_runtime_use_autosuspend(&pdev->dev);
- pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
-
irq = platform_get_irq(pdev, 0);
if (irq <= 0) {
ret = -ENXIO;
@@ -566,6 +567,9 @@
master->bits_per_word_mask = SPI_BPW_MASK(8);
+ pm_runtime_mark_last_busy(&pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
ret = spi_register_master(master);
if (ret) {
dev_err(&pdev->dev, "spi_register_master failed\n");
diff --git a/drivers/spi/spi-imx.c b/drivers/spi/spi-imx.c
index 39dc02e..4aee3db 100644
--- a/drivers/spi/spi-imx.c
+++ b/drivers/spi/spi-imx.c
@@ -506,7 +506,7 @@
{
struct spi_device *spi = msg->spi;
u32 ctrl = MX51_ECSPI_CTRL_ENABLE;
- u32 testreg;
+ u32 testreg, delay;
u32 cfg = readl(spi_imx->base + MX51_ECSPI_CONFIG);
/* set Master or Slave mode */
@@ -567,6 +567,23 @@
writel(cfg, spi_imx->base + MX51_ECSPI_CONFIG);
+ /*
+ * Wait until the changes in the configuration register CONFIGREG
+ * propagate into the hardware. It takes exactly one tick of the
+ * SCLK clock, but we will wait two SCLK clock just to be sure. The
+ * effect of the delay it takes for the hardware to apply changes
+ * is noticable if the SCLK clock run very slow. In such a case, if
+ * the polarity of SCLK should be inverted, the GPIO ChipSelect might
+ * be asserted before the SCLK polarity changes, which would disrupt
+ * the SPI communication as the device on the other end would consider
+ * the change of SCLK polarity as a clock tick already.
+ */
+ delay = (2 * 1000000) / spi_imx->spi_bus_clk;
+ if (likely(delay < 10)) /* SCLK is faster than 100 kHz */
+ udelay(delay);
+ else /* SCLK is _very_ slow */
+ usleep_range(delay, delay + 10);
+
return 0;
}
@@ -574,7 +591,7 @@
struct spi_device *spi)
{
u32 ctrl = readl(spi_imx->base + MX51_ECSPI_CTRL);
- u32 clk, delay;
+ u32 clk;
/* Clear BL field and set the right value */
ctrl &= ~MX51_ECSPI_CTRL_BL_MASK;
@@ -596,23 +613,6 @@
writel(ctrl, spi_imx->base + MX51_ECSPI_CTRL);
- /*
- * Wait until the changes in the configuration register CONFIGREG
- * propagate into the hardware. It takes exactly one tick of the
- * SCLK clock, but we will wait two SCLK clock just to be sure. The
- * effect of the delay it takes for the hardware to apply changes
- * is noticable if the SCLK clock run very slow. In such a case, if
- * the polarity of SCLK should be inverted, the GPIO ChipSelect might
- * be asserted before the SCLK polarity changes, which would disrupt
- * the SPI communication as the device on the other end would consider
- * the change of SCLK polarity as a clock tick already.
- */
- delay = (2 * 1000000) / clk;
- if (likely(delay < 10)) /* SCLK is faster than 100 kHz */
- udelay(delay);
- else /* SCLK is _very_ slow */
- usleep_range(delay, delay + 10);
-
return 0;
}
diff --git a/drivers/spi/spi-mt65xx.c b/drivers/spi/spi-mt65xx.c
index 976f73b..68dca8c 100644
--- a/drivers/spi/spi-mt65xx.c
+++ b/drivers/spi/spi-mt65xx.c
@@ -427,13 +427,23 @@
mtk_spi_setup_packet(master);
cnt = xfer->len / 4;
- iowrite32_rep(mdata->base + SPI_TX_DATA_REG, xfer->tx_buf, cnt);
+ if (xfer->tx_buf)
+ iowrite32_rep(mdata->base + SPI_TX_DATA_REG, xfer->tx_buf, cnt);
+
+ if (xfer->rx_buf)
+ ioread32_rep(mdata->base + SPI_RX_DATA_REG, xfer->rx_buf, cnt);
remainder = xfer->len % 4;
if (remainder > 0) {
reg_val = 0;
- memcpy(®_val, xfer->tx_buf + (cnt * 4), remainder);
- writel(reg_val, mdata->base + SPI_TX_DATA_REG);
+ if (xfer->tx_buf) {
+ memcpy(®_val, xfer->tx_buf + (cnt * 4), remainder);
+ writel(reg_val, mdata->base + SPI_TX_DATA_REG);
+ }
+ if (xfer->rx_buf) {
+ reg_val = readl(mdata->base + SPI_RX_DATA_REG);
+ memcpy(xfer->rx_buf + (cnt * 4), ®_val, remainder);
+ }
}
mtk_spi_enable_transfer(master);
@@ -793,12 +803,6 @@
pm_runtime_enable(&pdev->dev);
- ret = devm_spi_register_master(&pdev->dev, master);
- if (ret) {
- dev_err(&pdev->dev, "failed to register master (%d)\n", ret);
- goto err_disable_runtime_pm;
- }
-
if (mdata->dev_comp->need_pad_sel) {
if (mdata->pad_num != master->num_chipselect) {
dev_err(&pdev->dev,
@@ -838,6 +842,12 @@
dev_notice(&pdev->dev, "SPI dma_set_mask(%d) failed, ret:%d\n",
addr_bits, ret);
+ ret = devm_spi_register_master(&pdev->dev, master);
+ if (ret) {
+ dev_err(&pdev->dev, "failed to register master (%d)\n", ret);
+ goto err_disable_runtime_pm;
+ }
+
return 0;
err_disable_runtime_pm:
diff --git a/drivers/spi/spi-stm32.c b/drivers/spi/spi-stm32.c
index 8ffcffb..05618a6 100644
--- a/drivers/spi/spi-stm32.c
+++ b/drivers/spi/spi-stm32.c
@@ -884,15 +884,18 @@
ier = readl_relaxed(spi->base + STM32H7_SPI_IER);
mask = ier;
- /* EOTIE is triggered on EOT, SUSP and TXC events. */
+ /*
+ * EOTIE enables irq from EOT, SUSP and TXC events. We need to set
+ * SUSP to acknowledge it later. TXC is automatically cleared
+ */
+
mask |= STM32H7_SPI_SR_SUSP;
/*
- * When TXTF is set, DXPIE and TXPIE are cleared. So in case of
- * Full-Duplex, need to poll RXP event to know if there are remaining
- * data, before disabling SPI.
+ * DXPIE is set in Full-Duplex, one IT will be raised if TXP and RXP
+ * are set. So in case of Full-Duplex, need to poll TXP and RXP event.
*/
- if (spi->rx_buf && !spi->cur_usedma)
- mask |= STM32H7_SPI_SR_RXP;
+ if ((spi->cur_comm == SPI_FULL_DUPLEX) && !spi->cur_usedma)
+ mask |= STM32H7_SPI_SR_TXP | STM32H7_SPI_SR_RXP;
if (!(sr & mask)) {
dev_warn(spi->dev, "spurious IT (sr=0x%08x, ier=0x%08x)\n",
@@ -1925,6 +1928,7 @@
master->can_dma = stm32_spi_can_dma;
pm_runtime_set_active(&pdev->dev);
+ pm_runtime_get_noresume(&pdev->dev);
pm_runtime_enable(&pdev->dev);
ret = spi_register_master(master);
@@ -1940,6 +1944,8 @@
err_pm_disable:
pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
err_dma_release:
if (spi->dma_tx)
dma_release_channel(spi->dma_tx);
@@ -1956,9 +1962,14 @@
struct spi_master *master = platform_get_drvdata(pdev);
struct stm32_spi *spi = spi_master_get_devdata(master);
+ pm_runtime_get_sync(&pdev->dev);
+
spi_unregister_master(master);
spi->cfg->disable(spi);
+ pm_runtime_disable(&pdev->dev);
+ pm_runtime_put_noidle(&pdev->dev);
+ pm_runtime_set_suspended(&pdev->dev);
if (master->dma_tx)
dma_release_channel(master->dma_tx);
if (master->dma_rx)
@@ -1966,7 +1977,6 @@
clk_disable_unprepare(spi->clk);
- pm_runtime_disable(&pdev->dev);
pinctrl_pm_select_sleep_state(&pdev->dev);
