| // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause) |
| /* |
| * Copyright (c) 2021, Iskren Chernev <iskren.chernev@gmail.com> |
| */ |
| |
| #include <dt-bindings/clock/qcom,gcc-sm6115.h> |
| #include <dt-bindings/clock/qcom,sm6115-dispcc.h> |
| #include <dt-bindings/clock/qcom,rpmcc.h> |
| #include <dt-bindings/dma/qcom-gpi.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/power/qcom-rpmpd.h> |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| |
| chosen { }; |
| |
| clocks { |
| xo_board: xo-board { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| }; |
| |
| sleep_clk: sleep-clk { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| }; |
| }; |
| |
| cpus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| CPU0: cpu@0 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x0>; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| L2_0: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| }; |
| }; |
| |
| CPU1: cpu@1 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x1>; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| }; |
| |
| CPU2: cpu@2 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x2>; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| }; |
| |
| CPU3: cpu@3 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x3>; |
| capacity-dmips-mhz = <1024>; |
| dynamic-power-coefficient = <100>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_0>; |
| qcom,freq-domain = <&cpufreq_hw 0>; |
| }; |
| |
| CPU4: cpu@100 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x100>; |
| enable-method = "psci"; |
| capacity-dmips-mhz = <1638>; |
| dynamic-power-coefficient = <282>; |
| next-level-cache = <&L2_1>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| L2_1: l2-cache { |
| compatible = "cache"; |
| cache-level = <2>; |
| }; |
| }; |
| |
| CPU5: cpu@101 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x101>; |
| capacity-dmips-mhz = <1638>; |
| dynamic-power-coefficient = <282>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| }; |
| |
| CPU6: cpu@102 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x102>; |
| capacity-dmips-mhz = <1638>; |
| dynamic-power-coefficient = <282>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| }; |
| |
| CPU7: cpu@103 { |
| device_type = "cpu"; |
| compatible = "qcom,kryo260"; |
| reg = <0x0 0x103>; |
| capacity-dmips-mhz = <1638>; |
| dynamic-power-coefficient = <282>; |
| enable-method = "psci"; |
| next-level-cache = <&L2_1>; |
| qcom,freq-domain = <&cpufreq_hw 1>; |
| }; |
| |
| cpu-map { |
| cluster0 { |
| core0 { |
| cpu = <&CPU0>; |
| }; |
| |
| core1 { |
| cpu = <&CPU1>; |
| }; |
| |
| core2 { |
| cpu = <&CPU2>; |
| }; |
| |
| core3 { |
| cpu = <&CPU3>; |
| }; |
| }; |
| |
| cluster1 { |
| core0 { |
| cpu = <&CPU4>; |
| }; |
| |
| core1 { |
| cpu = <&CPU5>; |
| }; |
| |
| core2 { |
| cpu = <&CPU6>; |
| }; |
| |
| core3 { |
| cpu = <&CPU7>; |
| }; |
| }; |
| }; |
| }; |
| |
| firmware { |
| scm: scm { |
| compatible = "qcom,scm-sm6115", "qcom,scm"; |
| #reset-cells = <1>; |
| }; |
| }; |
| |
| memory@80000000 { |
| device_type = "memory"; |
| /* We expect the bootloader to fill in the size */ |
| reg = <0 0x80000000 0 0>; |
| }; |
| |
| pmu { |
| compatible = "arm,armv8-pmuv3"; |
| interrupts = <GIC_PPI 6 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| psci { |
| compatible = "arm,psci-1.0"; |
| method = "smc"; |
| }; |
| |
| reserved_memory: reserved-memory { |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| hyp_mem: memory@45700000 { |
| reg = <0x0 0x45700000 0x0 0x600000>; |
| no-map; |
| }; |
| |
| xbl_aop_mem: memory@45e00000 { |
| reg = <0x0 0x45e00000 0x0 0x140000>; |
| no-map; |
| }; |
| |
| sec_apps_mem: memory@45fff000 { |
| reg = <0x0 0x45fff000 0x0 0x1000>; |
| no-map; |
| }; |
| |
| smem_mem: memory@46000000 { |
| compatible = "qcom,smem"; |
| reg = <0x0 0x46000000 0x0 0x200000>; |
| no-map; |
| |
| hwlocks = <&tcsr_mutex 3>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| }; |
| |
| cdsp_sec_mem: memory@46200000 { |
| reg = <0x0 0x46200000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| pil_modem_mem: memory@4ab00000 { |
| reg = <0x0 0x4ab00000 0x0 0x6900000>; |
| no-map; |
| }; |
| |
| pil_video_mem: memory@51400000 { |
| reg = <0x0 0x51400000 0x0 0x500000>; |
| no-map; |
| }; |
| |
| wlan_msa_mem: memory@51900000 { |
| reg = <0x0 0x51900000 0x0 0x100000>; |
| no-map; |
| }; |
| |
| pil_cdsp_mem: memory@51a00000 { |
| reg = <0x0 0x51a00000 0x0 0x1e00000>; |
| no-map; |
| }; |
| |
| pil_adsp_mem: memory@53800000 { |
| reg = <0x0 0x53800000 0x0 0x2800000>; |
| no-map; |
| }; |
| |
| pil_ipa_fw_mem: memory@56100000 { |
| reg = <0x0 0x56100000 0x0 0x10000>; |
| no-map; |
| }; |
| |
| pil_ipa_gsi_mem: memory@56110000 { |
| reg = <0x0 0x56110000 0x0 0x5000>; |
| no-map; |
| }; |
| |
| pil_gpu_mem: memory@56115000 { |
| reg = <0x0 0x56115000 0x0 0x2000>; |
| no-map; |
| }; |
| |
| cont_splash_memory: memory@5c000000 { |
| reg = <0x0 0x5c000000 0x0 0x00f00000>; |
| no-map; |
| }; |
| |
| dfps_data_memory: memory@5cf00000 { |
| reg = <0x0 0x5cf00000 0x0 0x0100000>; |
| no-map; |
| }; |
| |
| removed_mem: memory@60000000 { |
| reg = <0x0 0x60000000 0x0 0x3900000>; |
| no-map; |
| }; |
| }; |
| |
| rpm-glink { |
| compatible = "qcom,glink-rpm"; |
| |
| interrupts = <GIC_SPI 194 IRQ_TYPE_EDGE_RISING>; |
| qcom,rpm-msg-ram = <&rpm_msg_ram>; |
| mboxes = <&apcs_glb 0>; |
| |
| rpm_requests: rpm-requests { |
| compatible = "qcom,rpm-sm6115"; |
| qcom,glink-channels = "rpm_requests"; |
| |
| rpmcc: clock-controller { |
| compatible = "qcom,rpmcc-sm6115", "qcom,rpmcc"; |
| clocks = <&xo_board>; |
| clock-names = "xo"; |
| #clock-cells = <1>; |
| }; |
| |
| rpmpd: power-controller { |
| compatible = "qcom,sm6115-rpmpd"; |
| #power-domain-cells = <1>; |
| operating-points-v2 = <&rpmpd_opp_table>; |
| |
| rpmpd_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| rpmpd_opp_min_svs: opp1 { |
| opp-level = <RPM_SMD_LEVEL_MIN_SVS>; |
| }; |
| |
| rpmpd_opp_low_svs: opp2 { |
| opp-level = <RPM_SMD_LEVEL_LOW_SVS>; |
| }; |
| |
| rpmpd_opp_svs: opp3 { |
| opp-level = <RPM_SMD_LEVEL_SVS>; |
| }; |
| |
| rpmpd_opp_svs_plus: opp4 { |
| opp-level = <RPM_SMD_LEVEL_SVS_PLUS>; |
| }; |
| |
| rpmpd_opp_nom: opp5 { |
| opp-level = <RPM_SMD_LEVEL_NOM>; |
| }; |
| |
| rpmpd_opp_nom_plus: opp6 { |
| opp-level = <RPM_SMD_LEVEL_NOM_PLUS>; |
| }; |
| |
| rpmpd_opp_turbo: opp7 { |
| opp-level = <RPM_SMD_LEVEL_TURBO>; |
| }; |
| |
| rpmpd_opp_turbo_plus: opp8 { |
| opp-level = <RPM_SMD_LEVEL_TURBO_NO_CPR>; |
| }; |
| }; |
| }; |
| }; |
| }; |
| |
| smp2p-adsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <443>, <429>; |
| |
| interrupts = <GIC_SPI 279 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs_glb 10>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <2>; |
| |
| adsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| adsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-cdsp { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <94>, <432>; |
| |
| interrupts = <GIC_SPI 263 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs_glb 30>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <5>; |
| |
| cdsp_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| cdsp_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| smp2p-mpss { |
| compatible = "qcom,smp2p"; |
| qcom,smem = <435>, <428>; |
| |
| interrupts = <GIC_SPI 70 IRQ_TYPE_EDGE_RISING>; |
| |
| mboxes = <&apcs_glb 14>; |
| |
| qcom,local-pid = <0>; |
| qcom,remote-pid = <1>; |
| |
| modem_smp2p_out: master-kernel { |
| qcom,entry-name = "master-kernel"; |
| #qcom,smem-state-cells = <1>; |
| }; |
| |
| modem_smp2p_in: slave-kernel { |
| qcom,entry-name = "slave-kernel"; |
| |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| }; |
| }; |
| |
| soc: soc@0 { |
| compatible = "simple-bus"; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges = <0 0 0 0 0x10 0>; |
| dma-ranges = <0 0 0 0 0x10 0>; |
| |
| tcsr_mutex: hwlock@340000 { |
| compatible = "qcom,tcsr-mutex"; |
| reg = <0x0 0x00340000 0x0 0x20000>; |
| #hwlock-cells = <1>; |
| }; |
| |
| tlmm: pinctrl@500000 { |
| compatible = "qcom,sm6115-tlmm"; |
| reg = <0x0 0x00500000 0x0 0x400000>, |
| <0x0 0x00900000 0x0 0x400000>, |
| <0x0 0x00d00000 0x0 0x400000>; |
| reg-names = "west", "south", "east"; |
| interrupts = <GIC_SPI 227 IRQ_TYPE_LEVEL_HIGH>; |
| gpio-controller; |
| gpio-ranges = <&tlmm 0 0 114>; /* GPIOs + ufs_reset */ |
| #gpio-cells = <2>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| |
| qup_i2c0_default: qup-i2c0-default-state { |
| pins = "gpio0", "gpio1"; |
| function = "qup0"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_i2c1_default: qup-i2c1-default-state { |
| pins = "gpio4", "gpio5"; |
| function = "qup1"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_i2c2_default: qup-i2c2-default-state { |
| pins = "gpio6", "gpio7"; |
| function = "qup2"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_i2c3_default: qup-i2c3-default-state { |
| pins = "gpio8", "gpio9"; |
| function = "qup3"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_i2c4_default: qup-i2c4-default-state { |
| pins = "gpio12", "gpio13"; |
| function = "qup4"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_i2c5_default: qup-i2c5-default-state { |
| pins = "gpio14", "gpio15"; |
| function = "qup5"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi0_default: qup-spi0-default-state { |
| pins = "gpio0", "gpio1","gpio2", "gpio3"; |
| function = "qup0"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi1_default: qup-spi1-default-state { |
| pins = "gpio4", "gpio5", "gpio69", "gpio70"; |
| function = "qup1"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi2_default: qup-spi2-default-state { |
| pins = "gpio6", "gpio7", "gpio71", "gpio80"; |
| function = "qup2"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi3_default: qup-spi3-default-state { |
| pins = "gpio8", "gpio9", "gpio10", "gpio11"; |
| function = "qup3"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi4_default: qup-spi4-default-state { |
| pins = "gpio12", "gpio13", "gpio96", "gpio97"; |
| function = "qup4"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| qup_spi5_default: qup-spi5-default-state { |
| pins = "gpio14", "gpio15", "gpio16", "gpio17"; |
| function = "qup5"; |
| drive-strength = <2>; |
| bias-pull-up; |
| }; |
| |
| sdc1_state_on: sdc1-on-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| |
| sdc1_state_off: sdc1-off-state { |
| clk-pins { |
| pins = "sdc1_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc1_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| data-pins { |
| pins = "sdc1_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| rclk-pins { |
| pins = "sdc1_rclk"; |
| bias-pull-down; |
| }; |
| }; |
| |
| sdc2_state_on: sdc2-on-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <16>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <10>; |
| }; |
| |
| sd-cd-pins { |
| pins = "gpio88"; |
| function = "gpio"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| }; |
| |
| sdc2_state_off: sdc2-off-state { |
| clk-pins { |
| pins = "sdc2_clk"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| |
| cmd-pins { |
| pins = "sdc2_cmd"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| data-pins { |
| pins = "sdc2_data"; |
| bias-pull-up; |
| drive-strength = <2>; |
| }; |
| |
| sd-cd-pins { |
| pins = "gpio88"; |
| function = "gpio"; |
| bias-disable; |
| drive-strength = <2>; |
| }; |
| }; |
| }; |
| |
| gcc: clock-controller@1400000 { |
| compatible = "qcom,gcc-sm6115"; |
| reg = <0x0 0x01400000 0x0 0x1f0000>; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&sleep_clk>; |
| clock-names = "bi_tcxo", "sleep_clk"; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| usb_1_hsphy: phy@1613000 { |
| compatible = "qcom,sm6115-qusb2-phy"; |
| reg = <0x0 0x01613000 0x0 0x180>; |
| #phy-cells = <0>; |
| |
| clocks = <&gcc GCC_AHB2PHY_USB_CLK>, <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "cfg_ahb", "ref"; |
| |
| resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>; |
| nvmem-cells = <&qusb2_hstx_trim>; |
| |
| status = "disabled"; |
| }; |
| |
| qfprom@1b40000 { |
| compatible = "qcom,sm6115-qfprom", "qcom,qfprom"; |
| reg = <0x0 0x01b40000 0x0 0x7000>; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| |
| qusb2_hstx_trim: hstx-trim@25b { |
| reg = <0x25b 0x1>; |
| bits = <1 4>; |
| }; |
| }; |
| |
| rng: rng@1b53000 { |
| compatible = "qcom,prng-ee"; |
| reg = <0x0 0x01b53000 0x0 0x1000>; |
| clocks = <&gcc GCC_PRNG_AHB_CLK>; |
| clock-names = "core"; |
| }; |
| |
| spmi_bus: spmi@1c40000 { |
| compatible = "qcom,spmi-pmic-arb"; |
| reg = <0x0 0x01c40000 0x0 0x1100>, |
| <0x0 0x01e00000 0x0 0x2000000>, |
| <0x0 0x03e00000 0x0 0x100000>, |
| <0x0 0x03f00000 0x0 0xa0000>, |
| <0x0 0x01c0a000 0x0 0x26000>; |
| reg-names = "core", "chnls", "obsrvr", "intr", "cnfg"; |
| interrupt-names = "periph_irq"; |
| interrupts = <GIC_SPI 183 IRQ_TYPE_LEVEL_HIGH>; |
| qcom,ee = <0>; |
| qcom,channel = <0>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| }; |
| |
| tsens0: thermal-sensor@4410000 { |
| compatible = "qcom,sm6115-tsens", "qcom,tsens-v2"; |
| reg = <0x0 0x04411000 0x0 0x1ff>, /* TM */ |
| <0x0 0x04410000 0x0 0x8>; /* SROT */ |
| #qcom,sensors = <16>; |
| interrupts = <GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 190 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "uplow", "critical"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| rpm_msg_ram: sram@45f0000 { |
| compatible = "qcom,rpm-msg-ram"; |
| reg = <0x0 0x045f0000 0x0 0x7000>; |
| }; |
| |
| sram@4690000 { |
| compatible = "qcom,rpm-stats"; |
| reg = <0x0 0x04690000 0x0 0x10000>; |
| }; |
| |
| sdhc_1: mmc@4744000 { |
| compatible = "qcom,sm6115-sdhci", "qcom,sdhci-msm-v5"; |
| reg = <0x0 0x04744000 0x0 0x1000>, |
| <0x0 0x04745000 0x0 0x1000>, |
| <0x0 0x04748000 0x0 0x8000>; |
| reg-names = "hc", "cqhci", "ice"; |
| |
| interrupts = <GIC_SPI 348 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 352 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC1_AHB_CLK>, |
| <&gcc GCC_SDCC1_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&gcc GCC_SDCC1_ICE_CORE_CLK>; |
| clock-names = "iface", "core", "xo", "ice"; |
| |
| pinctrl-0 = <&sdc1_state_on>; |
| pinctrl-1 = <&sdc1_state_off>; |
| pinctrl-names = "default", "sleep"; |
| |
| bus-width = <8>; |
| status = "disabled"; |
| }; |
| |
| sdhc_2: mmc@4784000 { |
| compatible = "qcom,sm6115-sdhci", "qcom,sdhci-msm-v5"; |
| reg = <0x0 0x04784000 0x0 0x1000>; |
| reg-names = "hc"; |
| |
| interrupts = <GIC_SPI 350 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hc_irq", "pwr_irq"; |
| |
| clocks = <&gcc GCC_SDCC2_AHB_CLK>, |
| <&gcc GCC_SDCC2_APPS_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "core", "xo"; |
| |
| pinctrl-0 = <&sdc2_state_on>; |
| pinctrl-1 = <&sdc2_state_off>; |
| pinctrl-names = "default", "sleep"; |
| |
| power-domains = <&rpmpd SM6115_VDDCX>; |
| operating-points-v2 = <&sdhc2_opp_table>; |
| iommus = <&apps_smmu 0x00a0 0x0>; |
| resets = <&gcc GCC_SDCC2_BCR>; |
| |
| bus-width = <4>; |
| qcom,dll-config = <0x0007642c>; |
| qcom,ddr-config = <0x80040868>; |
| status = "disabled"; |
| |
| sdhc2_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-100000000 { |
| opp-hz = /bits/ 64 <100000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| |
| opp-202000000 { |
| opp-hz = /bits/ 64 <202000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| ufs_mem_hc: ufs@4804000 { |
| compatible = "qcom,sm6115-ufshc", "qcom,ufshc", "jedec,ufs-2.0"; |
| reg = <0x0 0x04804000 0x0 0x3000>, <0x0 0x04810000 0x0 0x8000>; |
| reg-names = "std", "ice"; |
| interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&ufs_mem_phy_lanes>; |
| phy-names = "ufsphy"; |
| lanes-per-direction = <1>; |
| #reset-cells = <1>; |
| resets = <&gcc GCC_UFS_PHY_BCR>; |
| reset-names = "rst"; |
| |
| power-domains = <&gcc GCC_UFS_PHY_GDSC>; |
| iommus = <&apps_smmu 0x100 0>; |
| |
| clocks = <&gcc GCC_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_SYS_NOC_UFS_PHY_AXI_CLK>, |
| <&gcc GCC_UFS_PHY_AHB_CLK>, |
| <&gcc GCC_UFS_PHY_UNIPRO_CORE_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&gcc GCC_UFS_PHY_TX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_RX_SYMBOL_0_CLK>, |
| <&gcc GCC_UFS_PHY_ICE_CORE_CLK>; |
| clock-names = "core_clk", |
| "bus_aggr_clk", |
| "iface_clk", |
| "core_clk_unipro", |
| "ref_clk", |
| "tx_lane0_sync_clk", |
| "rx_lane0_sync_clk", |
| "ice_core_clk"; |
| |
| freq-table-hz = <50000000 200000000>, |
| <0 0>, |
| <0 0>, |
| <37500000 150000000>, |
| <0 0>, |
| <0 0>, |
| <0 0>, |
| <75000000 300000000>; |
| |
| status = "disabled"; |
| }; |
| |
| ufs_mem_phy: phy@4807000 { |
| compatible = "qcom,sm6115-qmp-ufs-phy"; |
| reg = <0x0 0x04807000 0x0 0x1c4>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_UFS_CLKREF_CLK>, <&gcc GCC_UFS_PHY_PHY_AUX_CLK>; |
| clock-names = "ref", "ref_aux"; |
| |
| resets = <&ufs_mem_hc 0>; |
| reset-names = "ufsphy"; |
| status = "disabled"; |
| |
| ufs_mem_phy_lanes: phy@4807400 { |
| reg = <0x0 0x04807400 0x0 0x098>, |
| <0x0 0x04807600 0x0 0x130>, |
| <0x0 0x04807c00 0x0 0x16c>; |
| #phy-cells = <0>; |
| }; |
| }; |
| |
| gpi_dma0: dma-controller@4a00000 { |
| compatible = "qcom,sm6115-gpi-dma", "qcom,sm6350-gpi-dma"; |
| reg = <0x0 0x04a00000 0x0 0x60000>; |
| interrupts = <GIC_SPI 335 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 336 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 337 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 338 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 339 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 340 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 342 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 343 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 344 IRQ_TYPE_LEVEL_HIGH>; |
| dma-channels = <10>; |
| dma-channel-mask = <0xf>; |
| iommus = <&apps_smmu 0xf6 0x0>; |
| #dma-cells = <3>; |
| status = "disabled"; |
| }; |
| |
| qupv3_id_0: geniqup@4ac0000 { |
| compatible = "qcom,geni-se-qup"; |
| reg = <0x0 0x04ac0000 0x0 0x2000>; |
| clock-names = "m-ahb", "s-ahb"; |
| clocks = <&gcc GCC_QUPV3_WRAP_0_M_AHB_CLK>, |
| <&gcc GCC_QUPV3_WRAP_0_S_AHB_CLK>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| iommus = <&apps_smmu 0xe3 0x0>; |
| ranges; |
| status = "disabled"; |
| |
| i2c0: i2c@4a80000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a80000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c0_default>; |
| interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 0 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi0: spi@4a80000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a80000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S0_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi0_default>; |
| interrupts = <GIC_SPI 327 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 0 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 0 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c1: i2c@4a84000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a84000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c1_default>; |
| interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 1 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi1: spi@4a84000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a84000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S1_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi1_default>; |
| interrupts = <GIC_SPI 328 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 1 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 1 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c2: i2c@4a88000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a88000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c2_default>; |
| interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 2 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi2: spi@4a88000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a88000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S2_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi2_default>; |
| interrupts = <GIC_SPI 329 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 2 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 2 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c3: i2c@4a8c000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a8c000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c3_default>; |
| interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 3 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi3: spi@4a8c000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a8c000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S3_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi3_default>; |
| interrupts = <GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 3 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 3 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| i2c4: i2c@4a90000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a90000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c4_default>; |
| interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 4 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi4: spi@4a90000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a90000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi4_default>; |
| interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 4 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 4 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| uart4: serial@4a90000 { |
| compatible = "qcom,geni-debug-uart"; |
| reg = <0x0 0x04a90000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>; |
| interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| i2c5: i2c@4a94000 { |
| compatible = "qcom,geni-i2c"; |
| reg = <0x0 0x04a94000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_i2c5_default>; |
| interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_I2C>, |
| <&gpi_dma0 1 5 QCOM_GPI_I2C>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| |
| spi5: spi@4a94000 { |
| compatible = "qcom,geni-spi"; |
| reg = <0x0 0x04a94000 0x0 0x4000>; |
| clock-names = "se"; |
| clocks = <&gcc GCC_QUPV3_WRAP0_S5_CLK>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&qup_spi5_default>; |
| interrupts = <GIC_SPI 332 IRQ_TYPE_LEVEL_HIGH>; |
| dmas = <&gpi_dma0 0 5 QCOM_GPI_SPI>, |
| <&gpi_dma0 1 5 QCOM_GPI_SPI>; |
| dma-names = "tx", "rx"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "disabled"; |
| }; |
| }; |
| |
| usb_1: usb@4ef8800 { |
| compatible = "qcom,sm6115-dwc3", "qcom,dwc3"; |
| reg = <0x0 0x04ef8800 0x0 0x400>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| clocks = <&gcc GCC_CFG_NOC_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>, |
| <&gcc GCC_SYS_NOC_USB3_PRIM_AXI_CLK>, |
| <&gcc GCC_USB30_PRIM_SLEEP_CLK>, |
| <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB3_PRIM_CLKREF_CLK>; |
| clock-names = "cfg_noc", "core", "iface", "sleep", "mock_utmi", "xo"; |
| |
| assigned-clocks = <&gcc GCC_USB30_PRIM_MOCK_UTMI_CLK>, |
| <&gcc GCC_USB30_PRIM_MASTER_CLK>; |
| assigned-clock-rates = <19200000>, <66666667>; |
| |
| interrupts = <GIC_SPI 260 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "hs_phy_irq", "ss_phy_irq"; |
| |
| resets = <&gcc GCC_USB30_PRIM_BCR>; |
| power-domains = <&gcc GCC_USB30_PRIM_GDSC>; |
| qcom,select-utmi-as-pipe-clk; |
| status = "disabled"; |
| |
| usb_1_dwc3: usb@4e00000 { |
| compatible = "snps,dwc3"; |
| reg = <0x0 0x04e00000 0x0 0xcd00>; |
| interrupts = <GIC_SPI 255 IRQ_TYPE_LEVEL_HIGH>; |
| phys = <&usb_1_hsphy>; |
| phy-names = "usb2-phy"; |
| iommus = <&apps_smmu 0x120 0x0>; |
| snps,dis_u2_susphy_quirk; |
| snps,dis_enblslpm_quirk; |
| snps,has-lpm-erratum; |
| snps,hird-threshold = /bits/ 8 <0x10>; |
| snps,usb3_lpm_capable; |
| maximum-speed = "high-speed"; |
| dr_mode = "peripheral"; |
| }; |
| }; |
| |
| mdss: display-subsystem@5e00000 { |
| compatible = "qcom,sm6115-mdss"; |
| reg = <0x0 0x05e00000 0x0 0x1000>; |
| reg-names = "mdss"; |
| |
| power-domains = <&dispcc MDSS_GDSC>; |
| |
| clocks = <&gcc GCC_DISP_AHB_CLK>, |
| <&gcc GCC_DISP_HF_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>; |
| |
| interrupts = <GIC_SPI 186 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <1>; |
| |
| iommus = <&apps_smmu 0x420 0x2>, |
| <&apps_smmu 0x421 0x0>; |
| |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| |
| status = "disabled"; |
| |
| mdp: display-controller@5e01000 { |
| compatible = "qcom,sm6115-dpu"; |
| reg = <0x0 0x05e01000 0x0 0x8f000>, |
| <0x0 0x05eb0000 0x0 0x2008>; |
| reg-names = "mdp", "vbif"; |
| |
| clocks = <&gcc GCC_DISP_HF_AXI_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_CLK>, |
| <&dispcc DISP_CC_MDSS_MDP_LUT_CLK>, |
| <&dispcc DISP_CC_MDSS_ROT_CLK>, |
| <&dispcc DISP_CC_MDSS_VSYNC_CLK>; |
| clock-names = "bus", |
| "iface", |
| "core", |
| "lut", |
| "rot", |
| "vsync"; |
| |
| operating-points-v2 = <&mdp_opp_table>; |
| power-domains = <&rpmpd SM6115_VDDCX>; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <0>; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| dpu_intf1_out: endpoint { |
| remote-endpoint = <&mdss_dsi0_in>; |
| }; |
| }; |
| }; |
| |
| mdp_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmpd_opp_min_svs>; |
| }; |
| |
| opp-192000000 { |
| opp-hz = /bits/ 64 <192000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| |
| opp-256000000 { |
| opp-hz = /bits/ 64 <256000000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| |
| opp-307200000 { |
| opp-hz = /bits/ 64 <307200000>; |
| required-opps = <&rpmpd_opp_svs_plus>; |
| }; |
| |
| opp-384000000 { |
| opp-hz = /bits/ 64 <384000000>; |
| required-opps = <&rpmpd_opp_nom>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0: dsi@5e94000 { |
| compatible = "qcom,dsi-ctrl-6g-qcm2290"; |
| reg = <0x0 0x05e94000 0x0 0x400>; |
| reg-names = "dsi_ctrl"; |
| |
| interrupt-parent = <&mdss>; |
| interrupts = <4>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK>, |
| <&dispcc DISP_CC_MDSS_BYTE0_INTF_CLK>, |
| <&dispcc DISP_CC_MDSS_PCLK0_CLK>, |
| <&dispcc DISP_CC_MDSS_ESC0_CLK>, |
| <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&gcc GCC_DISP_HF_AXI_CLK>; |
| clock-names = "byte", |
| "byte_intf", |
| "pixel", |
| "core", |
| "iface", |
| "bus"; |
| |
| assigned-clocks = <&dispcc DISP_CC_MDSS_BYTE0_CLK_SRC>, |
| <&dispcc DISP_CC_MDSS_PCLK0_CLK_SRC>; |
| assigned-clock-parents = <&mdss_dsi0_phy 0>, <&mdss_dsi0_phy 1>; |
| |
| operating-points-v2 = <&dsi_opp_table>; |
| power-domains = <&rpmpd SM6115_VDDCX>; |
| phys = <&mdss_dsi0_phy>; |
| |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| |
| ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| mdss_dsi0_in: endpoint { |
| remote-endpoint = <&dpu_intf1_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| mdss_dsi0_out: endpoint { |
| }; |
| }; |
| }; |
| |
| dsi_opp_table: opp-table { |
| compatible = "operating-points-v2"; |
| |
| opp-19200000 { |
| opp-hz = /bits/ 64 <19200000>; |
| required-opps = <&rpmpd_opp_min_svs>; |
| }; |
| |
| opp-164000000 { |
| opp-hz = /bits/ 64 <164000000>; |
| required-opps = <&rpmpd_opp_low_svs>; |
| }; |
| |
| opp-187500000 { |
| opp-hz = /bits/ 64 <187500000>; |
| required-opps = <&rpmpd_opp_svs>; |
| }; |
| }; |
| }; |
| |
| mdss_dsi0_phy: phy@5e94400 { |
| compatible = "qcom,dsi-phy-14nm-2290"; |
| reg = <0x0 0x05e94400 0x0 0x100>, |
| <0x0 0x05e94500 0x0 0x300>, |
| <0x0 0x05e94800 0x0 0x188>; |
| reg-names = "dsi_phy", |
| "dsi_phy_lane", |
| "dsi_pll"; |
| |
| #clock-cells = <1>; |
| #phy-cells = <0>; |
| |
| clocks = <&dispcc DISP_CC_MDSS_AHB_CLK>, |
| <&rpmcc RPM_SMD_XO_CLK_SRC>; |
| clock-names = "iface", "ref"; |
| |
| status = "disabled"; |
| }; |
| }; |
| |
| dispcc: clock-controller@5f00000 { |
| compatible = "qcom,sm6115-dispcc"; |
| reg = <0x0 0x05f00000 0 0x20000>; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, |
| <&sleep_clk>, |
| <&mdss_dsi0_phy 0>, |
| <&mdss_dsi0_phy 1>, |
| <&gcc GCC_DISP_GPLL0_DIV_CLK_SRC>; |
| #clock-cells = <1>; |
| #reset-cells = <1>; |
| #power-domain-cells = <1>; |
| }; |
| |
| stm@8002000 { |
| compatible = "arm,coresight-stm", "arm,primecell"; |
| reg = <0x0 0x08002000 0x0 0x1000>, |
| <0x0 0x0e280000 0x0 0x180000>; |
| reg-names = "stm-base", "stm-stimulus-base"; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| stm_out: endpoint { |
| remote-endpoint = <&funnel_in0_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| cti0: cti@8010000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08010000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti1: cti@8011000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08011000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti2: cti@8012000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08012000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti3: cti@8013000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08013000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti4: cti@8014000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08014000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti5: cti@8015000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08015000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti6: cti@8016000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08016000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti7: cti@8017000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08017000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti8: cti@8018000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08018000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti9: cti@8019000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x08019000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti10: cti@801a000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801a000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti11: cti@801b000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801b000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti12: cti@801c000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801c000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti13: cti@801d000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801d000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti14: cti@801e000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801e000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| cti15: cti@801f000 { |
| compatible = "arm,coresight-cti", "arm,primecell"; |
| reg = <0x0 0x0801f000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| }; |
| |
| replicator@8046000 { |
| compatible = "arm,coresight-dynamic-replicator", "arm,primecell"; |
| reg = <0x0 0x08046000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| replicator_out: endpoint { |
| remote-endpoint = <&etr_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| replicator_in: endpoint { |
| remote-endpoint = <&etf_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| etf@8047000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x0 0x08047000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| in-ports { |
| port { |
| etf_in: endpoint { |
| remote-endpoint = <&merge_funnel_out>; |
| }; |
| }; |
| }; |
| |
| out-ports { |
| port { |
| etf_out: endpoint { |
| remote-endpoint = <&replicator_in>; |
| }; |
| }; |
| }; |
| }; |
| |
| etr@8048000 { |
| compatible = "arm,coresight-tmc", "arm,primecell"; |
| reg = <0x0 0x08048000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| in-ports { |
| port { |
| etr_in: endpoint { |
| remote-endpoint = <&replicator_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@8041000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x0 0x08041000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| funnel_in0_out: endpoint { |
| remote-endpoint = <&merge_funnel_in0>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| funnel_in0_in: endpoint { |
| remote-endpoint = <&stm_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@8042000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x0 0x08042000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| funnel_in1_out: endpoint { |
| remote-endpoint = <&merge_funnel_in1>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| funnel_in1_in: endpoint { |
| remote-endpoint = <&funnel_apss1_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@8045000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x0 0x08045000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| merge_funnel_out: endpoint { |
| remote-endpoint = <&etf_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| merge_funnel_in0: endpoint { |
| remote-endpoint = <&funnel_in0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| merge_funnel_in1: endpoint { |
| remote-endpoint = <&funnel_in1_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9040000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09040000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU0>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm0_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in0>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9140000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09140000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU1>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm1_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in1>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9240000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09240000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU2>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm2_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in2>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9340000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09340000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU3>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm3_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in3>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9440000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09440000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU4>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm4_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in4>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9540000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09540000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU5>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm5_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in5>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9640000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09640000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU6>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm6_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in6>; |
| }; |
| }; |
| }; |
| }; |
| |
| etm@9740000 { |
| compatible = "arm,coresight-etm4x", "arm,primecell"; |
| reg = <0x0 0x09740000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| arm,coresight-loses-context-with-cpu; |
| |
| cpu = <&CPU7>; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| etm7_out: endpoint { |
| remote-endpoint = <&funnel_apss0_in7>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@9800000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x0 0x09800000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| funnel_apss0_out: endpoint { |
| remote-endpoint = <&funnel_apss1_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| port@0 { |
| reg = <0>; |
| funnel_apss0_in0: endpoint { |
| remote-endpoint = <&etm0_out>; |
| }; |
| }; |
| |
| port@1 { |
| reg = <1>; |
| funnel_apss0_in1: endpoint { |
| remote-endpoint = <&etm1_out>; |
| }; |
| }; |
| |
| port@2 { |
| reg = <2>; |
| funnel_apss0_in2: endpoint { |
| remote-endpoint = <&etm2_out>; |
| }; |
| }; |
| |
| port@3 { |
| reg = <3>; |
| funnel_apss0_in3: endpoint { |
| remote-endpoint = <&etm3_out>; |
| }; |
| }; |
| |
| port@4 { |
| reg = <4>; |
| funnel_apss0_in4: endpoint { |
| remote-endpoint = <&etm4_out>; |
| }; |
| }; |
| |
| port@5 { |
| reg = <5>; |
| funnel_apss0_in5: endpoint { |
| remote-endpoint = <&etm5_out>; |
| }; |
| }; |
| |
| port@6 { |
| reg = <6>; |
| funnel_apss0_in6: endpoint { |
| remote-endpoint = <&etm6_out>; |
| }; |
| }; |
| |
| port@7 { |
| reg = <7>; |
| funnel_apss0_in7: endpoint { |
| remote-endpoint = <&etm7_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| funnel@9810000 { |
| compatible = "arm,coresight-dynamic-funnel", "arm,primecell"; |
| reg = <0x0 0x09810000 0x0 0x1000>; |
| |
| clocks = <&rpmcc RPM_SMD_QDSS_CLK>; |
| clock-names = "apb_pclk"; |
| |
| status = "disabled"; |
| |
| out-ports { |
| port { |
| funnel_apss1_out: endpoint { |
| remote-endpoint = <&funnel_in1_in>; |
| }; |
| }; |
| }; |
| |
| in-ports { |
| port { |
| funnel_apss1_in: endpoint { |
| remote-endpoint = <&funnel_apss0_out>; |
| }; |
| }; |
| }; |
| }; |
| |
| apps_smmu: iommu@c600000 { |
| compatible = "qcom,sm6115-smmu-500", "qcom,smmu-500", "arm,mmu-500"; |
| reg = <0x0 0x0c600000 0x0 0x80000>; |
| #iommu-cells = <2>; |
| #global-interrupts = <1>; |
| |
| interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 88 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 95 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 97 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 99 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 103 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 107 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 113 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 115 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 116 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 117 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 118 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 124 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 125 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 126 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 127 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 128 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 136 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 137 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 138 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 139 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 144 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 145 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 146 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 147 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| wifi: wifi@c800000 { |
| compatible = "qcom,wcn3990-wifi"; |
| reg = <0x0 0x0c800000 0x0 0x800000>; |
| reg-names = "membase"; |
| memory-region = <&wlan_msa_mem>; |
| interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 359 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 360 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 361 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 362 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 363 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 364 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 365 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 366 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 367 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 368 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 369 IRQ_TYPE_LEVEL_HIGH>; |
| iommus = <&apps_smmu 0x1a0 0x1>; |
| qcom,msa-fixed-perm; |
| status = "disabled"; |
| }; |
| |
| watchdog@f017000 { |
| compatible = "qcom,apss-wdt-sm6115", "qcom,kpss-wdt"; |
| reg = <0x0 0x0f017000 0x0 0x1000>; |
| clocks = <&sleep_clk>; |
| interrupts = <GIC_SPI 3 IRQ_TYPE_EDGE_RISING>; |
| }; |
| |
| apcs_glb: mailbox@f111000 { |
| compatible = "qcom,sm6115-apcs-hmss-global"; |
| reg = <0x0 0x0f111000 0x0 0x1000>; |
| |
| #mbox-cells = <1>; |
| }; |
| |
| timer@f120000 { |
| compatible = "arm,armv7-timer-mem"; |
| reg = <0x0 0x0f120000 0x0 0x1000>; |
| #address-cells = <2>; |
| #size-cells = <2>; |
| ranges; |
| clock-frequency = <19200000>; |
| |
| frame@f121000 { |
| reg = <0x0 0x0f121000 0x0 0x1000>, <0x0 0x0f122000 0x0 0x1000>; |
| frame-number = <0>; |
| interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| frame@f123000 { |
| reg = <0x0 0x0f123000 0x0 0x1000>; |
| frame-number = <1>; |
| interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| frame@f124000 { |
| reg = <0x0 0x0f124000 0x0 0x1000>; |
| frame-number = <2>; |
| interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| frame@f125000 { |
| reg = <0x0 0x0f125000 0x0 0x1000>; |
| frame-number = <3>; |
| interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| frame@f126000 { |
| reg = <0x0 0x0f126000 0x0 0x1000>; |
| frame-number = <4>; |
| interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| frame@f127000 { |
| reg = <0x0 0x0f127000 0x0 0x1000>; |
| frame-number = <5>; |
| interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| |
| frame@f128000 { |
| reg = <0x0 0x0f128000 0x0 0x1000>; |
| frame-number = <6>; |
| interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>; |
| status = "disabled"; |
| }; |
| }; |
| |
| intc: interrupt-controller@f200000 { |
| compatible = "arm,gic-v3"; |
| reg = <0x0 0x0f200000 0x0 0x10000>, |
| <0x0 0x0f300000 0x0 0x100000>; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| interrupt-parent = <&intc>; |
| #redistributor-regions = <1>; |
| redistributor-stride = <0x0 0x20000>; |
| interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH>; |
| }; |
| |
| cpufreq_hw: cpufreq@f521000 { |
| compatible = "qcom,cpufreq-hw"; |
| reg = <0x0 0x0f521000 0x0 0x1000>, |
| <0x0 0x0f523000 0x0 0x1000>; |
| |
| reg-names = "freq-domain0", "freq-domain1"; |
| clocks = <&rpmcc RPM_SMD_XO_CLK_SRC>, <&gcc GPLL0>; |
| clock-names = "xo", "alternate"; |
| |
| #freq-domain-cells = <1>; |
| }; |
| }; |
| |
| thermal-zones { |
| mapss-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 0>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| cdsp-hvx-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 1>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| wlan-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 2>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| camera-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 3>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| video-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 4>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| modem1-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 5>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| cpu4-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 6>; |
| |
| trips { |
| cpu4_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu4_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu5-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 7>; |
| |
| trips { |
| cpu5_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu5_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu6-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 8>; |
| |
| trips { |
| cpu6_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu6_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu7-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 9>; |
| |
| trips { |
| cpu7_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu7_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu45-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 10>; |
| |
| trips { |
| cpu45_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu45_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu45_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu67-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 11>; |
| |
| trips { |
| cpu67_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu67_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu67_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| cpu0123-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 12>; |
| |
| trips { |
| cpu0123_alert0: trip-point0 { |
| temperature = <90000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0123_alert1: trip-point1 { |
| temperature = <95000>; |
| hysteresis = <2000>; |
| type = "passive"; |
| }; |
| |
| cpu0123_crit: cpu_crit { |
| temperature = <110000>; |
| hysteresis = <1000>; |
| type = "critical"; |
| }; |
| }; |
| }; |
| |
| modem0-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 13>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| display-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 14>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| gpu-thermal { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-sensors = <&tsens0 15>; |
| |
| trips { |
| trip-point0 { |
| temperature = <115000>; |
| hysteresis = <5000>; |
| type = "passive"; |
| }; |
| |
| trip-point1 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| timer { |
| compatible = "arm,armv8-timer"; |
| interrupts = <GIC_PPI 1 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 3 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>, |
| <GIC_PPI 0 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>; |
| }; |
| }; |
