Merge branches 'clk-cdce-regulator', 'clk-bcm', 'clk-evict-parent-cache' and 'clk-actions' into clk-next
- Add regulator support to the cdce925 clk driver
- Add support for Raspberry Pi 4 bcm2711 SoCs
- Evict parents from parent cache when they're unregistered
* clk-cdce-regulator:
clk: clk-cdce925: Add regulator support
dt-bindings: clock: cdce925: Add regulator documentation
* clk-bcm:
clk: bcm2835: Mark PLLD_PER as CRITICAL
clk: bcm2835: Add BCM2711_CLOCK_EMMC2 support
clk: bcm2835: Introduce SoC specific clock registration
dt-bindings: bcm2835-cprman: Add bcm2711 support
* clk-evict-parent-cache:
clk: Evict unregistered clks from parent caches
* clk-actions:
clk: actions: Fix factor clk struct member access
diff --git a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt
index dd906db..9e0b03a 100644
--- a/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt
+++ b/Documentation/devicetree/bindings/clock/brcm,bcm2835-cprman.txt
@@ -12,7 +12,9 @@
the PLL dividers directly.
Required properties:
-- compatible: Should be "brcm,bcm2835-cprman"
+- compatible: should be one of the following,
+ "brcm,bcm2711-cprman"
+ "brcm,bcm2835-cprman"
- #clock-cells: Should be <1>. The permitted clock-specifier values can be
found in include/dt-bindings/clock/bcm2835.h
- reg: Specifies base physical address and size of the registers
diff --git a/Documentation/devicetree/bindings/clock/ti,cdce925.txt b/Documentation/devicetree/bindings/clock/ti,cdce925.txt
index 0d01f2d..26544c8 100644
--- a/Documentation/devicetree/bindings/clock/ti,cdce925.txt
+++ b/Documentation/devicetree/bindings/clock/ti,cdce925.txt
@@ -24,6 +24,8 @@
Optional properties:
- xtal-load-pf: Crystal load-capacitor value to fine-tune performance on a
board, or to compensate for external influences.
+- vdd-supply: A regulator node for Vdd
+- vddout-supply: A regulator node for Vddout
For all PLL1, PLL2, ... an optional child node can be used to specify spread
spectrum clocking parameters for a board.
@@ -41,6 +43,8 @@
clocks = <&xtal_27Mhz>;
#clock-cells = <1>;
xtal-load-pf = <5>;
+ vdd-supply = <&1v8-reg>;
+ vddout-supply = <&3v3-reg>;
/* PLL options to get SSC 1% centered */
PLL2 {
spread-spectrum = <4>;
diff --git a/drivers/clk/actions/owl-factor.c b/drivers/clk/actions/owl-factor.c
index 317d4a9..f15e262 100644
--- a/drivers/clk/actions/owl-factor.c
+++ b/drivers/clk/actions/owl-factor.c
@@ -64,11 +64,10 @@
return val;
}
-static int clk_val_best(struct clk_hw *hw, unsigned long rate,
+static int owl_clk_val_best(const struct owl_factor_hw *factor_hw,
+ struct clk_hw *hw, unsigned long rate,
unsigned long *best_parent_rate)
{
- struct owl_factor *factor = hw_to_owl_factor(hw);
- struct owl_factor_hw *factor_hw = &factor->factor_hw;
const struct clk_factor_table *clkt = factor_hw->table;
unsigned long parent_rate, try_parent_rate, best = 0, cur_rate;
unsigned long parent_rate_saved = *best_parent_rate;
@@ -126,7 +125,7 @@
const struct clk_factor_table *clkt = factor_hw->table;
unsigned int val, mul = 0, div = 1;
- val = clk_val_best(&common->hw, rate, parent_rate);
+ val = owl_clk_val_best(factor_hw, &common->hw, rate, parent_rate);
_get_table_div_mul(clkt, val, &mul, &div);
return *parent_rate * mul / div;
diff --git a/drivers/clk/bcm/clk-bcm2835.c b/drivers/clk/bcm/clk-bcm2835.c
index 867ae3c..802e488 100644
--- a/drivers/clk/bcm/clk-bcm2835.c
+++ b/drivers/clk/bcm/clk-bcm2835.c
@@ -31,7 +31,7 @@
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/module.h>
-#include <linux/of.h>
+#include <linux/of_device.h>
#include <linux/platform_device.h>
#include <linux/slab.h>
#include <dt-bindings/clock/bcm2835.h>
@@ -114,6 +114,8 @@
#define CM_AVEODIV 0x1bc
#define CM_EMMCCTL 0x1c0
#define CM_EMMCDIV 0x1c4
+#define CM_EMMC2CTL 0x1d0
+#define CM_EMMC2DIV 0x1d4
/* General bits for the CM_*CTL regs */
# define CM_ENABLE BIT(4)
@@ -289,6 +291,10 @@
#define LOCK_TIMEOUT_NS 100000000
#define BCM2835_MAX_FB_RATE 1750000000u
+#define SOC_BCM2835 BIT(0)
+#define SOC_BCM2711 BIT(1)
+#define SOC_ALL (SOC_BCM2835 | SOC_BCM2711)
+
/*
* Names of clocks used within the driver that need to be replaced
* with an external parent's name. This array is in the order that
@@ -320,6 +326,10 @@
struct clk_hw_onecell_data onecell;
};
+struct cprman_plat_data {
+ unsigned int soc;
+};
+
static inline void cprman_write(struct bcm2835_cprman *cprman, u32 reg, u32 val)
{
writel(CM_PASSWORD | val, cprman->regs + reg);
@@ -1451,22 +1461,28 @@
const void *data);
struct bcm2835_clk_desc {
bcm2835_clk_register clk_register;
+ unsigned int supported;
const void *data;
};
/* assignment helper macros for different clock types */
-#define _REGISTER(f, ...) { .clk_register = (bcm2835_clk_register)f, \
- .data = __VA_ARGS__ }
-#define REGISTER_PLL(...) _REGISTER(&bcm2835_register_pll, \
+#define _REGISTER(f, s, ...) { .clk_register = (bcm2835_clk_register)f, \
+ .supported = s, \
+ .data = __VA_ARGS__ }
+#define REGISTER_PLL(s, ...) _REGISTER(&bcm2835_register_pll, \
+ s, \
&(struct bcm2835_pll_data) \
{__VA_ARGS__})
-#define REGISTER_PLL_DIV(...) _REGISTER(&bcm2835_register_pll_divider, \
- &(struct bcm2835_pll_divider_data) \
- {__VA_ARGS__})
-#define REGISTER_CLK(...) _REGISTER(&bcm2835_register_clock, \
+#define REGISTER_PLL_DIV(s, ...) _REGISTER(&bcm2835_register_pll_divider, \
+ s, \
+ &(struct bcm2835_pll_divider_data) \
+ {__VA_ARGS__})
+#define REGISTER_CLK(s, ...) _REGISTER(&bcm2835_register_clock, \
+ s, \
&(struct bcm2835_clock_data) \
{__VA_ARGS__})
-#define REGISTER_GATE(...) _REGISTER(&bcm2835_register_gate, \
+#define REGISTER_GATE(s, ...) _REGISTER(&bcm2835_register_gate, \
+ s, \
&(struct bcm2835_gate_data) \
{__VA_ARGS__})
@@ -1480,7 +1496,8 @@
"testdebug1"
};
-#define REGISTER_OSC_CLK(...) REGISTER_CLK( \
+#define REGISTER_OSC_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_clock_osc_parents), \
.parents = bcm2835_clock_osc_parents, \
__VA_ARGS__)
@@ -1497,7 +1514,8 @@
"pllh_aux",
};
-#define REGISTER_PER_CLK(...) REGISTER_CLK( \
+#define REGISTER_PER_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_clock_per_parents), \
.parents = bcm2835_clock_per_parents, \
__VA_ARGS__)
@@ -1522,7 +1540,8 @@
"-",
};
-#define REGISTER_PCM_CLK(...) REGISTER_CLK( \
+#define REGISTER_PCM_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_pcm_per_parents), \
.parents = bcm2835_pcm_per_parents, \
__VA_ARGS__)
@@ -1541,7 +1560,8 @@
"pllc_core2",
};
-#define REGISTER_VPU_CLK(...) REGISTER_CLK( \
+#define REGISTER_VPU_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_clock_vpu_parents), \
.parents = bcm2835_clock_vpu_parents, \
__VA_ARGS__)
@@ -1577,12 +1597,14 @@
"dsi1_byte_inv",
};
-#define REGISTER_DSI0_CLK(...) REGISTER_CLK( \
+#define REGISTER_DSI0_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_clock_dsi0_parents), \
.parents = bcm2835_clock_dsi0_parents, \
__VA_ARGS__)
-#define REGISTER_DSI1_CLK(...) REGISTER_CLK( \
+#define REGISTER_DSI1_CLK(s, ...) REGISTER_CLK( \
+ s, \
.num_mux_parents = ARRAY_SIZE(bcm2835_clock_dsi1_parents), \
.parents = bcm2835_clock_dsi1_parents, \
__VA_ARGS__)
@@ -1602,6 +1624,7 @@
* AUDIO domain is on.
*/
[BCM2835_PLLA] = REGISTER_PLL(
+ SOC_ALL,
.name = "plla",
.cm_ctrl_reg = CM_PLLA,
.a2w_ctrl_reg = A2W_PLLA_CTRL,
@@ -1616,6 +1639,7 @@
.max_rate = 2400000000u,
.max_fb_rate = BCM2835_MAX_FB_RATE),
[BCM2835_PLLA_CORE] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plla_core",
.source_pll = "plla",
.cm_reg = CM_PLLA,
@@ -1625,6 +1649,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLA_PER] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plla_per",
.source_pll = "plla",
.cm_reg = CM_PLLA,
@@ -1634,6 +1659,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLA_DSI0] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plla_dsi0",
.source_pll = "plla",
.cm_reg = CM_PLLA,
@@ -1642,6 +1668,7 @@
.hold_mask = CM_PLLA_HOLDDSI0,
.fixed_divider = 1),
[BCM2835_PLLA_CCP2] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plla_ccp2",
.source_pll = "plla",
.cm_reg = CM_PLLA,
@@ -1663,6 +1690,7 @@
* AUDIO domain is on.
*/
[BCM2835_PLLC] = REGISTER_PLL(
+ SOC_ALL,
.name = "pllc",
.cm_ctrl_reg = CM_PLLC,
.a2w_ctrl_reg = A2W_PLLC_CTRL,
@@ -1677,6 +1705,7 @@
.max_rate = 3000000000u,
.max_fb_rate = BCM2835_MAX_FB_RATE),
[BCM2835_PLLC_CORE0] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "pllc_core0",
.source_pll = "pllc",
.cm_reg = CM_PLLC,
@@ -1686,6 +1715,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLC_CORE1] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "pllc_core1",
.source_pll = "pllc",
.cm_reg = CM_PLLC,
@@ -1695,6 +1725,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLC_CORE2] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "pllc_core2",
.source_pll = "pllc",
.cm_reg = CM_PLLC,
@@ -1704,6 +1735,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLC_PER] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "pllc_per",
.source_pll = "pllc",
.cm_reg = CM_PLLC,
@@ -1720,6 +1752,7 @@
* AUDIO domain is on.
*/
[BCM2835_PLLD] = REGISTER_PLL(
+ SOC_ALL,
.name = "plld",
.cm_ctrl_reg = CM_PLLD,
.a2w_ctrl_reg = A2W_PLLD_CTRL,
@@ -1734,6 +1767,7 @@
.max_rate = 2400000000u,
.max_fb_rate = BCM2835_MAX_FB_RATE),
[BCM2835_PLLD_CORE] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plld_core",
.source_pll = "plld",
.cm_reg = CM_PLLD,
@@ -1742,7 +1776,13 @@
.hold_mask = CM_PLLD_HOLDCORE,
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
+ /*
+ * VPU firmware assumes that PLLD_PER isn't disabled by the ARM core.
+ * Otherwise this could cause firmware lookups. That's why we mark
+ * it as critical.
+ */
[BCM2835_PLLD_PER] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plld_per",
.source_pll = "plld",
.cm_reg = CM_PLLD,
@@ -1750,8 +1790,9 @@
.load_mask = CM_PLLD_LOADPER,
.hold_mask = CM_PLLD_HOLDPER,
.fixed_divider = 1,
- .flags = CLK_SET_RATE_PARENT),
+ .flags = CLK_IS_CRITICAL | CLK_SET_RATE_PARENT),
[BCM2835_PLLD_DSI0] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plld_dsi0",
.source_pll = "plld",
.cm_reg = CM_PLLD,
@@ -1760,6 +1801,7 @@
.hold_mask = CM_PLLD_HOLDDSI0,
.fixed_divider = 1),
[BCM2835_PLLD_DSI1] = REGISTER_PLL_DIV(
+ SOC_ALL,
.name = "plld_dsi1",
.source_pll = "plld",
.cm_reg = CM_PLLD,
@@ -1775,6 +1817,7 @@
* It is in the HDMI power domain.
*/
[BCM2835_PLLH] = REGISTER_PLL(
+ SOC_BCM2835,
"pllh",
.cm_ctrl_reg = CM_PLLH,
.a2w_ctrl_reg = A2W_PLLH_CTRL,
@@ -1789,6 +1832,7 @@
.max_rate = 3000000000u,
.max_fb_rate = BCM2835_MAX_FB_RATE),
[BCM2835_PLLH_RCAL] = REGISTER_PLL_DIV(
+ SOC_BCM2835,
.name = "pllh_rcal",
.source_pll = "pllh",
.cm_reg = CM_PLLH,
@@ -1798,6 +1842,7 @@
.fixed_divider = 10,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLH_AUX] = REGISTER_PLL_DIV(
+ SOC_BCM2835,
.name = "pllh_aux",
.source_pll = "pllh",
.cm_reg = CM_PLLH,
@@ -1807,6 +1852,7 @@
.fixed_divider = 1,
.flags = CLK_SET_RATE_PARENT),
[BCM2835_PLLH_PIX] = REGISTER_PLL_DIV(
+ SOC_BCM2835,
.name = "pllh_pix",
.source_pll = "pllh",
.cm_reg = CM_PLLH,
@@ -1822,6 +1868,7 @@
/* One Time Programmable Memory clock. Maximum 10Mhz. */
[BCM2835_CLOCK_OTP] = REGISTER_OSC_CLK(
+ SOC_ALL,
.name = "otp",
.ctl_reg = CM_OTPCTL,
.div_reg = CM_OTPDIV,
@@ -1833,6 +1880,7 @@
* bythe watchdog timer and the camera pulse generator.
*/
[BCM2835_CLOCK_TIMER] = REGISTER_OSC_CLK(
+ SOC_ALL,
.name = "timer",
.ctl_reg = CM_TIMERCTL,
.div_reg = CM_TIMERDIV,
@@ -1843,12 +1891,14 @@
* Generally run at 2Mhz, max 5Mhz.
*/
[BCM2835_CLOCK_TSENS] = REGISTER_OSC_CLK(
+ SOC_ALL,
.name = "tsens",
.ctl_reg = CM_TSENSCTL,
.div_reg = CM_TSENSDIV,
.int_bits = 5,
.frac_bits = 0),
[BCM2835_CLOCK_TEC] = REGISTER_OSC_CLK(
+ SOC_ALL,
.name = "tec",
.ctl_reg = CM_TECCTL,
.div_reg = CM_TECDIV,
@@ -1857,6 +1907,7 @@
/* clocks with vpu parent mux */
[BCM2835_CLOCK_H264] = REGISTER_VPU_CLK(
+ SOC_ALL,
.name = "h264",
.ctl_reg = CM_H264CTL,
.div_reg = CM_H264DIV,
@@ -1864,6 +1915,7 @@
.frac_bits = 8,
.tcnt_mux = 1),
[BCM2835_CLOCK_ISP] = REGISTER_VPU_CLK(
+ SOC_ALL,
.name = "isp",
.ctl_reg = CM_ISPCTL,
.div_reg = CM_ISPDIV,
@@ -1876,6 +1928,7 @@
* in the SDRAM controller can't be used.
*/
[BCM2835_CLOCK_SDRAM] = REGISTER_VPU_CLK(
+ SOC_ALL,
.name = "sdram",
.ctl_reg = CM_SDCCTL,
.div_reg = CM_SDCDIV,
@@ -1883,6 +1936,7 @@
.frac_bits = 0,
.tcnt_mux = 3),
[BCM2835_CLOCK_V3D] = REGISTER_VPU_CLK(
+ SOC_ALL,
.name = "v3d",
.ctl_reg = CM_V3DCTL,
.div_reg = CM_V3DDIV,
@@ -1896,6 +1950,7 @@
* in various hardware documentation.
*/
[BCM2835_CLOCK_VPU] = REGISTER_VPU_CLK(
+ SOC_ALL,
.name = "vpu",
.ctl_reg = CM_VPUCTL,
.div_reg = CM_VPUDIV,
@@ -1907,6 +1962,7 @@
/* clocks with per parent mux */
[BCM2835_CLOCK_AVEO] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "aveo",
.ctl_reg = CM_AVEOCTL,
.div_reg = CM_AVEODIV,
@@ -1914,6 +1970,7 @@
.frac_bits = 0,
.tcnt_mux = 38),
[BCM2835_CLOCK_CAM0] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "cam0",
.ctl_reg = CM_CAM0CTL,
.div_reg = CM_CAM0DIV,
@@ -1921,6 +1978,7 @@
.frac_bits = 8,
.tcnt_mux = 14),
[BCM2835_CLOCK_CAM1] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "cam1",
.ctl_reg = CM_CAM1CTL,
.div_reg = CM_CAM1DIV,
@@ -1928,12 +1986,14 @@
.frac_bits = 8,
.tcnt_mux = 15),
[BCM2835_CLOCK_DFT] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "dft",
.ctl_reg = CM_DFTCTL,
.div_reg = CM_DFTDIV,
.int_bits = 5,
.frac_bits = 0),
[BCM2835_CLOCK_DPI] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "dpi",
.ctl_reg = CM_DPICTL,
.div_reg = CM_DPIDIV,
@@ -1943,6 +2003,7 @@
/* Arasan EMMC clock */
[BCM2835_CLOCK_EMMC] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "emmc",
.ctl_reg = CM_EMMCCTL,
.div_reg = CM_EMMCDIV,
@@ -1950,8 +2011,19 @@
.frac_bits = 8,
.tcnt_mux = 39),
+ /* EMMC2 clock (only available for BCM2711) */
+ [BCM2711_CLOCK_EMMC2] = REGISTER_PER_CLK(
+ SOC_BCM2711,
+ .name = "emmc2",
+ .ctl_reg = CM_EMMC2CTL,
+ .div_reg = CM_EMMC2DIV,
+ .int_bits = 4,
+ .frac_bits = 8,
+ .tcnt_mux = 42),
+
/* General purpose (GPIO) clocks */
[BCM2835_CLOCK_GP0] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "gp0",
.ctl_reg = CM_GP0CTL,
.div_reg = CM_GP0DIV,
@@ -1960,6 +2032,7 @@
.is_mash_clock = true,
.tcnt_mux = 20),
[BCM2835_CLOCK_GP1] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "gp1",
.ctl_reg = CM_GP1CTL,
.div_reg = CM_GP1DIV,
@@ -1969,6 +2042,7 @@
.is_mash_clock = true,
.tcnt_mux = 21),
[BCM2835_CLOCK_GP2] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "gp2",
.ctl_reg = CM_GP2CTL,
.div_reg = CM_GP2DIV,
@@ -1978,6 +2052,7 @@
/* HDMI state machine */
[BCM2835_CLOCK_HSM] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "hsm",
.ctl_reg = CM_HSMCTL,
.div_reg = CM_HSMDIV,
@@ -1985,6 +2060,7 @@
.frac_bits = 8,
.tcnt_mux = 22),
[BCM2835_CLOCK_PCM] = REGISTER_PCM_CLK(
+ SOC_ALL,
.name = "pcm",
.ctl_reg = CM_PCMCTL,
.div_reg = CM_PCMDIV,
@@ -1994,6 +2070,7 @@
.low_jitter = true,
.tcnt_mux = 23),
[BCM2835_CLOCK_PWM] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "pwm",
.ctl_reg = CM_PWMCTL,
.div_reg = CM_PWMDIV,
@@ -2002,6 +2079,7 @@
.is_mash_clock = true,
.tcnt_mux = 24),
[BCM2835_CLOCK_SLIM] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "slim",
.ctl_reg = CM_SLIMCTL,
.div_reg = CM_SLIMDIV,
@@ -2010,6 +2088,7 @@
.is_mash_clock = true,
.tcnt_mux = 25),
[BCM2835_CLOCK_SMI] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "smi",
.ctl_reg = CM_SMICTL,
.div_reg = CM_SMIDIV,
@@ -2017,6 +2096,7 @@
.frac_bits = 8,
.tcnt_mux = 27),
[BCM2835_CLOCK_UART] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "uart",
.ctl_reg = CM_UARTCTL,
.div_reg = CM_UARTDIV,
@@ -2026,6 +2106,7 @@
/* TV encoder clock. Only operating frequency is 108Mhz. */
[BCM2835_CLOCK_VEC] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "vec",
.ctl_reg = CM_VECCTL,
.div_reg = CM_VECDIV,
@@ -2040,6 +2121,7 @@
/* dsi clocks */
[BCM2835_CLOCK_DSI0E] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "dsi0e",
.ctl_reg = CM_DSI0ECTL,
.div_reg = CM_DSI0EDIV,
@@ -2047,6 +2129,7 @@
.frac_bits = 8,
.tcnt_mux = 18),
[BCM2835_CLOCK_DSI1E] = REGISTER_PER_CLK(
+ SOC_ALL,
.name = "dsi1e",
.ctl_reg = CM_DSI1ECTL,
.div_reg = CM_DSI1EDIV,
@@ -2054,6 +2137,7 @@
.frac_bits = 8,
.tcnt_mux = 19),
[BCM2835_CLOCK_DSI0P] = REGISTER_DSI0_CLK(
+ SOC_ALL,
.name = "dsi0p",
.ctl_reg = CM_DSI0PCTL,
.div_reg = CM_DSI0PDIV,
@@ -2061,6 +2145,7 @@
.frac_bits = 0,
.tcnt_mux = 12),
[BCM2835_CLOCK_DSI1P] = REGISTER_DSI1_CLK(
+ SOC_ALL,
.name = "dsi1p",
.ctl_reg = CM_DSI1PCTL,
.div_reg = CM_DSI1PDIV,
@@ -2077,6 +2162,7 @@
* non-stop vpu clock.
*/
[BCM2835_CLOCK_PERI_IMAGE] = REGISTER_GATE(
+ SOC_ALL,
.name = "peri_image",
.parent = "vpu",
.ctl_reg = CM_PERIICTL),
@@ -2109,9 +2195,14 @@
struct resource *res;
const struct bcm2835_clk_desc *desc;
const size_t asize = ARRAY_SIZE(clk_desc_array);
+ const struct cprman_plat_data *pdata;
size_t i;
int ret;
+ pdata = of_device_get_match_data(&pdev->dev);
+ if (!pdata)
+ return -ENODEV;
+
cprman = devm_kzalloc(dev,
struct_size(cprman, onecell.hws, asize),
GFP_KERNEL);
@@ -2147,8 +2238,10 @@
for (i = 0; i < asize; i++) {
desc = &clk_desc_array[i];
- if (desc->clk_register && desc->data)
+ if (desc->clk_register && desc->data &&
+ (desc->supported & pdata->soc)) {
hws[i] = desc->clk_register(cprman, desc->data);
+ }
}
ret = bcm2835_mark_sdc_parent_critical(hws[BCM2835_CLOCK_SDRAM]->clk);
@@ -2159,8 +2252,17 @@
&cprman->onecell);
}
+static const struct cprman_plat_data cprman_bcm2835_plat_data = {
+ .soc = SOC_BCM2835,
+};
+
+static const struct cprman_plat_data cprman_bcm2711_plat_data = {
+ .soc = SOC_BCM2711,
+};
+
static const struct of_device_id bcm2835_clk_of_match[] = {
- { .compatible = "brcm,bcm2835-cprman", },
+ { .compatible = "brcm,bcm2835-cprman", .data = &cprman_bcm2835_plat_data },
+ { .compatible = "brcm,bcm2711-cprman", .data = &cprman_bcm2711_plat_data },
{}
};
MODULE_DEVICE_TABLE(of, bcm2835_clk_of_match);
diff --git a/drivers/clk/clk-cdce925.c b/drivers/clk/clk-cdce925.c
index 23c9326..308b353 100644
--- a/drivers/clk/clk-cdce925.c
+++ b/drivers/clk/clk-cdce925.c
@@ -16,6 +16,7 @@
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/regmap.h>
+#include <linux/regulator/consumer.h>
#include <linux/slab.h>
#include <linux/gcd.h>
@@ -602,6 +603,30 @@
return &data->clk[idx].hw;
}
+static void cdce925_regulator_disable(void *regulator)
+{
+ regulator_disable(regulator);
+}
+
+static int cdce925_regulator_enable(struct device *dev, const char *name)
+{
+ struct regulator *regulator;
+ int err;
+
+ regulator = devm_regulator_get(dev, name);
+ if (IS_ERR(regulator))
+ return PTR_ERR(regulator);
+
+ err = regulator_enable(regulator);
+ if (err) {
+ dev_err(dev, "Failed to enable %s: %d\n", name, err);
+ return err;
+ }
+
+ return devm_add_action_or_reset(dev, cdce925_regulator_disable,
+ regulator);
+}
+
/* The CDCE925 uses a funky way to read/write registers. Bulk mode is
* just weird, so just use the single byte mode exclusively. */
static struct regmap_bus regmap_cdce925_bus = {
@@ -630,6 +655,15 @@
};
dev_dbg(&client->dev, "%s\n", __func__);
+
+ err = cdce925_regulator_enable(&client->dev, "vdd");
+ if (err)
+ return err;
+
+ err = cdce925_regulator_enable(&client->dev, "vddout");
+ if (err)
+ return err;
+
data = devm_kzalloc(&client->dev, sizeof(*data), GFP_KERNEL);
if (!data)
return -ENOMEM;
diff --git a/drivers/clk/clk.c b/drivers/clk/clk.c
index e7300e1..498cae5 100644
--- a/drivers/clk/clk.c
+++ b/drivers/clk/clk.c
@@ -37,6 +37,12 @@
static HLIST_HEAD(clk_orphan_list);
static LIST_HEAD(clk_notifier_list);
+static struct hlist_head *all_lists[] = {
+ &clk_root_list,
+ &clk_orphan_list,
+ NULL,
+};
+
/*** private data structures ***/
struct clk_parent_map {
@@ -2841,12 +2847,6 @@
static DEFINE_MUTEX(clk_debug_lock);
static HLIST_HEAD(clk_debug_list);
-static struct hlist_head *all_lists[] = {
- &clk_root_list,
- &clk_orphan_list,
- NULL,
-};
-
static struct hlist_head *orphan_list[] = {
&clk_orphan_list,
NULL,
@@ -3777,6 +3777,34 @@
.set_parent = clk_nodrv_set_parent,
};
+static void clk_core_evict_parent_cache_subtree(struct clk_core *root,
+ struct clk_core *target)
+{
+ int i;
+ struct clk_core *child;
+
+ for (i = 0; i < root->num_parents; i++)
+ if (root->parents[i].core == target)
+ root->parents[i].core = NULL;
+
+ hlist_for_each_entry(child, &root->children, child_node)
+ clk_core_evict_parent_cache_subtree(child, target);
+}
+
+/* Remove this clk from all parent caches */
+static void clk_core_evict_parent_cache(struct clk_core *core)
+{
+ struct hlist_head **lists;
+ struct clk_core *root;
+
+ lockdep_assert_held(&prepare_lock);
+
+ for (lists = all_lists; *lists; lists++)
+ hlist_for_each_entry(root, *lists, child_node)
+ clk_core_evict_parent_cache_subtree(root, core);
+
+}
+
/**
* clk_unregister - unregister a currently registered clock
* @clk: clock to unregister
@@ -3815,6 +3843,8 @@
clk_core_set_parent_nolock(child, NULL);
}
+ clk_core_evict_parent_cache(clk->core);
+
hlist_del_init(&clk->core->child_node);
if (clk->core->prepare_count)
diff --git a/include/dt-bindings/clock/bcm2835.h b/include/dt-bindings/clock/bcm2835.h
index 2cec01f..b60c0343 100644
--- a/include/dt-bindings/clock/bcm2835.h
+++ b/include/dt-bindings/clock/bcm2835.h
@@ -58,3 +58,5 @@
#define BCM2835_CLOCK_DSI1E 48
#define BCM2835_CLOCK_DSI0P 49
#define BCM2835_CLOCK_DSI1P 50
+
+#define BCM2711_CLOCK_EMMC2 51
