blob: 2f3997740068db3956ed5bc7ae8ced06b7e5b8b4 [file] [log] [blame]
// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
/*
* Google Gru (and derivatives) board device tree source
*
* Copyright 2016-2017 Google, Inc
*/
#include <dt-bindings/input/input.h>
#include "rk3399.dtsi"
#include "rk3399-op1-opp.dtsi"
/ {
chosen {
stdout-path = "serial2:115200n8";
};
/*
* Power Tree
*
* In general an attempt is made to include all rails called out by
* the schematic as long as those rails interact in some way with
* the AP. AKA:
* - Rails that only connect to the EC (or devices that the EC talks to)
* are not included.
* - Rails _are_ included if the rails go to the AP even if the AP
* doesn't currently care about them / they are always on. The idea
* here is that it makes it easier to map to the schematic or extend
* later.
*
* If two rails are substantially the same from the AP's point of
* view, though, we won't create a full fixed regulator. We'll just
* put the child rail as an alias of the parent rail. Sometimes rails
* look the same to the AP because one of these is true:
* - The EC controls the enable and the EC always enables a rail as
* long as the AP is running.
* - The rails are actually connected to each other by a jumper and
* the distinction is just there to add clarity/flexibility to the
* schematic.
*/
ppvar_sys: ppvar-sys {
compatible = "regulator-fixed";
regulator-name = "ppvar_sys";
regulator-always-on;
regulator-boot-on;
};
pp1200_lpddr: pp1200-lpddr {
compatible = "regulator-fixed";
regulator-name = "pp1200_lpddr";
/* EC turns on w/ lpddr_pwr_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
vin-supply = <&ppvar_sys>;
};
pp1800: pp1800 {
compatible = "regulator-fixed";
regulator-name = "pp1800";
/* Always on when ppvar_sys shows power good */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
vin-supply = <&ppvar_sys>;
};
pp3300: pp3300 {
compatible = "regulator-fixed";
regulator-name = "pp3300";
/* Always on; plain and simple */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
vin-supply = <&ppvar_sys>;
};
pp5000: pp5000 {
compatible = "regulator-fixed";
regulator-name = "pp5000";
/* EC turns on w/ pp5000_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
vin-supply = <&ppvar_sys>;
};
ppvar_bigcpu_pwm: ppvar-bigcpu-pwm {
compatible = "pwm-regulator";
regulator-name = "ppvar_bigcpu_pwm";
pwms = <&pwm1 0 3337 0>;
pwm-supply = <&ppvar_sys>;
pwm-dutycycle-range = <100 0>;
pwm-dutycycle-unit = <100>;
/* EC turns on w/ ap_core_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <800107>;
regulator-max-microvolt = <1302232>;
};
ppvar_bigcpu: ppvar-bigcpu {
compatible = "vctrl-regulator";
regulator-name = "ppvar_bigcpu";
regulator-min-microvolt = <800107>;
regulator-max-microvolt = <1302232>;
ctrl-supply = <&ppvar_bigcpu_pwm>;
ctrl-voltage-range = <800107 1302232>;
regulator-settling-time-up-us = <322>;
};
ppvar_litcpu_pwm: ppvar-litcpu-pwm {
compatible = "pwm-regulator";
regulator-name = "ppvar_litcpu_pwm";
pwms = <&pwm2 0 3337 0>;
pwm-supply = <&ppvar_sys>;
pwm-dutycycle-range = <100 0>;
pwm-dutycycle-unit = <100>;
/* EC turns on w/ ap_core_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <797743>;
regulator-max-microvolt = <1307837>;
};
ppvar_litcpu: ppvar-litcpu {
compatible = "vctrl-regulator";
regulator-name = "ppvar_litcpu";
regulator-min-microvolt = <797743>;
regulator-max-microvolt = <1307837>;
ctrl-supply = <&ppvar_litcpu_pwm>;
ctrl-voltage-range = <797743 1307837>;
regulator-settling-time-up-us = <384>;
};
ppvar_gpu_pwm: ppvar-gpu-pwm {
compatible = "pwm-regulator";
regulator-name = "ppvar_gpu_pwm";
pwms = <&pwm0 0 3337 0>;
pwm-supply = <&ppvar_sys>;
pwm-dutycycle-range = <100 0>;
pwm-dutycycle-unit = <100>;
/* EC turns on w/ ap_core_en; always on for AP */
regulator-always-on;
regulator-boot-on;
regulator-min-microvolt = <786384>;
regulator-max-microvolt = <1217747>;
};
ppvar_gpu: ppvar-gpu {
compatible = "vctrl-regulator";
regulator-name = "ppvar_gpu";
regulator-min-microvolt = <786384>;
regulator-max-microvolt = <1217747>;
ctrl-supply = <&ppvar_gpu_pwm>;
ctrl-voltage-range = <786384 1217747>;
regulator-settling-time-up-us = <390>;
};
/* EC turns on w/ pp900_ddrpll_en */
pp900_ddrpll: pp900-ap {
};
/* EC turns on w/ pp900_pll_en */
pp900_pll: pp900-ap {
};
/* EC turns on w/ pp900_pmu_en */
pp900_pmu: pp900-ap {
};
/* EC turns on w/ pp1800_s0_en_l */
pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: pp1800 {
};
/* EC turns on w/ pp1800_avdd_en_l */
pp1800_avdd: pp1800 {
};
/* EC turns on w/ pp1800_lid_en_l */
pp1800_lid: pp1800_mic: pp1800 {
};
/* EC turns on w/ lpddr_pwr_en */
pp1800_lpddr: pp1800 {
};
/* EC turns on w/ pp1800_pmu_en_l */
pp1800_pmu: pp1800 {
};
/* EC turns on w/ pp1800_usb_en_l */
pp1800_usb: pp1800 {
};
pp3000_sd_slot: pp3000-sd-slot {
compatible = "regulator-fixed";
regulator-name = "pp3000_sd_slot";
pinctrl-names = "default";
pinctrl-0 = <&sd_slot_pwr_en>;
enable-active-high;
gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
vin-supply = <&pp3000>;
};
/*
* Technically, this is a small abuse of 'regulator-gpio'; this
* regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are
* always on though, so it is sufficient to simply control the mux
* here.
*/
ppvar_sd_card_io: ppvar-sd-card-io {
compatible = "regulator-gpio";
regulator-name = "ppvar_sd_card_io";
pinctrl-names = "default";
pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>;
enable-active-high;
enable-gpio = <&gpio2 2 GPIO_ACTIVE_HIGH>;
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
states = <1800000 0x1
3000000 0x0>;
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <3000000>;
};
/* EC turns on w/ pp3300_trackpad_en_l */
pp3300_trackpad: pp3300-trackpad {
};
/* EC turns on w/ usb_a_en */
pp5000_usb_a_vbus: pp5000 {
};
ap_rtc_clk: ap-rtc-clk {
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "xin32k";
#clock-cells = <0>;
};
max98357a: max98357a {
compatible = "maxim,max98357a";
pinctrl-names = "default";
pinctrl-0 = <&sdmode_en>;
sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
sdmode-delay = <2>;
#sound-dai-cells = <0>;
status = "okay";
};
sound: sound {
compatible = "rockchip,rk3399-gru-sound";
rockchip,cpu = <&i2s0 &i2s2>;
};
};
&cdn_dp {
status = "okay";
};
/*
* Set some suspend operating points to avoid OVP in suspend
*
* When we go into S3 ARM Trusted Firmware will transition our PWM regulators
* from wherever they're at back to the "default" operating point (whatever
* voltage we get when we set the PWM pins to "input").
*
* This quick transition under light load has the possibility to trigger the
* regulator "over voltage protection" (OVP).
*
* To make extra certain that we don't hit this OVP at suspend time, we'll
* transition to a voltage that's much closer to the default (~1.0 V) so that
* there will not be a big jump. Technically we only need to get within 200 mV
* of the default voltage, but the speed here should be fast enough and we need
* suspend/resume to be rock solid.
*/
&cluster0_opp {
opp05 {
opp-suspend;
};
};
&cluster1_opp {
opp06 {
opp-suspend;
};
};
&cpu_l0 {
cpu-supply = <&ppvar_litcpu>;
};
&cpu_l1 {
cpu-supply = <&ppvar_litcpu>;
};
&cpu_l2 {
cpu-supply = <&ppvar_litcpu>;
};
&cpu_l3 {
cpu-supply = <&ppvar_litcpu>;
};
&cpu_b0 {
cpu-supply = <&ppvar_bigcpu>;
};
&cpu_b1 {
cpu-supply = <&ppvar_bigcpu>;
};
&cru {
assigned-clocks =
<&cru PLL_GPLL>, <&cru PLL_CPLL>,
<&cru PLL_NPLL>,
<&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>,
<&cru PCLK_PERIHP>,
<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>,
<&cru PCLK_PERILP0>, <&cru ACLK_CCI>,
<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>,
<&cru ACLK_VIO>, <&cru ACLK_HDCP>,
<&cru ACLK_GIC_PRE>,
<&cru PCLK_DDR>;
assigned-clock-rates =
<600000000>, <800000000>,
<1000000000>,
<150000000>, <75000000>,
<37500000>,
<100000000>, <100000000>,
<50000000>, <800000000>,
<100000000>, <50000000>,
<400000000>, <400000000>,
<200000000>,
<200000000>;
};
&emmc_phy {
status = "okay";
};
&gpu {
mali-supply = <&ppvar_gpu>;
status = "okay";
};
ap_i2c_ts: &i2c3 {
status = "okay";
clock-frequency = <400000>;
/* These are relatively safe rise/fall times */
i2c-scl-falling-time-ns = <50>;
i2c-scl-rising-time-ns = <300>;
};
ap_i2c_audio: &i2c8 {
status = "okay";
clock-frequency = <400000>;
/* These are relatively safe rise/fall times */
i2c-scl-falling-time-ns = <50>;
i2c-scl-rising-time-ns = <300>;
codec: da7219@1a {
compatible = "dlg,da7219";
reg = <0x1a>;
interrupt-parent = <&gpio1>;
interrupts = <23 IRQ_TYPE_LEVEL_LOW>;
clocks = <&cru SCLK_I2S_8CH_OUT>;
clock-names = "mclk";
dlg,micbias-lvl = <2600>;
dlg,mic-amp-in-sel = "diff";
pinctrl-names = "default";
pinctrl-0 = <&headset_int_l>;
VDD-supply = <&pp1800>;
VDDMIC-supply = <&pp3300>;
VDDIO-supply = <&pp1800>;
da7219_aad {
dlg,adc-1bit-rpt = <1>;
dlg,btn-avg = <4>;
dlg,btn-cfg = <50>;
dlg,mic-det-thr = <500>;
dlg,jack-ins-deb = <20>;
dlg,jack-det-rate = "32ms_64ms";
dlg,jack-rem-deb = <1>;
dlg,a-d-btn-thr = <0xa>;
dlg,d-b-btn-thr = <0x16>;
dlg,b-c-btn-thr = <0x21>;
dlg,c-mic-btn-thr = <0x3E>;
};
};
};
&i2s0 {
status = "okay";
};
&i2s2 {
status = "okay";
};
&io_domains {
status = "okay";
audio-supply = <&pp1800_audio>; /* APIO5_VDD; 3d 4a */
bt656-supply = <&pp1800_ap_io>; /* APIO2_VDD; 2a 2b */
gpio1830-supply = <&pp3000_ap>; /* APIO4_VDD; 4c 4d */
sdmmc-supply = <&ppvar_sd_card_io>; /* SDMMC0_VDD; 4b */
};
&pcie0 {
status = "okay";
ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>;
vpcie3v3-supply = <&pp3300_wifi_bt>;
vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */
vpcie0v9-supply = <&pp900_pcie>;
pci_rootport: pcie@0,0 {
reg = <0x83000000 0x0 0x00000000 0x0 0x00000000>;
#address-cells = <3>;
#size-cells = <2>;
ranges;
};
};
&pcie_phy {
status = "okay";
};
&pmu_io_domains {
status = "okay";
pmu1830-supply = <&pp1800_pmu>; /* PMUIO2_VDD */
};
&pwm0 {
status = "okay";
};
&pwm1 {
status = "okay";
};
&pwm2 {
status = "okay";
};
&pwm3 {
status = "okay";
};
&sdhci {
/*
* Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the
* same (or nearly the same) performance for all eMMC that are intended
* to be used.
*/
assigned-clock-rates = <150000000>;
bus-width = <8>;
mmc-hs400-1_8v;
mmc-hs400-enhanced-strobe;
non-removable;
status = "okay";
};
&sdmmc {
status = "okay";
/*
* Note: configure "sdmmc_cd" as card detect even though it's actually
* hooked to ground. Because we specified "cd-gpios" below dw_mmc
* should be ignoring card detect anyway. Specifying the pin as
* sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag)
* turned on that the system will still make sure the port is
* configured as SDMMC and not JTAG.
*/
pinctrl-names = "default";
pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_gpio
&sdmmc_bus4>;
bus-width = <4>;
cap-mmc-highspeed;
cap-sd-highspeed;
cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>;
disable-wp;
sd-uhs-sdr12;
sd-uhs-sdr25;
sd-uhs-sdr50;
sd-uhs-sdr104;
vmmc-supply = <&pp3000_sd_slot>;
vqmmc-supply = <&ppvar_sd_card_io>;
};
&spi1 {
status = "okay";
pinctrl-names = "default", "sleep";
pinctrl-1 = <&spi1_sleep>;
spiflash@0 {
compatible = "jedec,spi-nor";
reg = <0>;
/* May run faster once verified. */
spi-max-frequency = <10000000>;
};
};
&spi2 {
status = "okay";
};
&spi5 {
status = "okay";
cros_ec: ec@0 {
compatible = "google,cros-ec-spi";
reg = <0>;
interrupt-parent = <&gpio0>;
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
pinctrl-names = "default";
pinctrl-0 = <&ec_ap_int_l>;
spi-max-frequency = <3000000>;
i2c_tunnel: i2c-tunnel {
compatible = "google,cros-ec-i2c-tunnel";
google,remote-bus = <4>;
#address-cells = <1>;
#size-cells = <0>;
};
usbc_extcon0: extcon0 {
compatible = "google,extcon-usbc-cros-ec";
google,usb-port-id = <0>;
};
};
};
&tsadc {
status = "okay";
rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */
rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */
};
&tcphy0 {
status = "okay";
extcon = <&usbc_extcon0>;
};
&u2phy0 {
status = "okay";
};
&u2phy0_host {
status = "okay";
};
&u2phy1_host {
status = "okay";
};
&u2phy0_otg {
status = "okay";
};
&u2phy1_otg {
status = "okay";
};
&uart2 {
status = "okay";
};
&usb_host0_ohci {
status = "okay";
};
&usbdrd3_0 {
status = "okay";
extcon = <&usbc_extcon0>;
};
&usbdrd_dwc3_0 {
status = "okay";
dr_mode = "host";
};
&vopb {
status = "okay";
};
&vopb_mmu {
status = "okay";
};
&vopl {
status = "okay";
};
&vopl_mmu {
status = "okay";
};
#include <arm/cros-ec-keyboard.dtsi>
#include <arm/cros-ec-sbs.dtsi>
&pinctrl {
/*
* pinctrl settings for pins that have no real owners.
*
* At the moment settings are identical for S0 and S3, but if we later
* need to configure things differently for S3 we'll adjust here.
*/
pinctrl-names = "default";
pinctrl-0 = <
&ap_pwroff /* AP will auto-assert this when in S3 */
&clk_32k /* This pin is always 32k on gru boards */
>;
pcfg_output_low: pcfg-output-low {
output-low;
};
pcfg_output_high: pcfg-output-high {
output-high;
};
pcfg_pull_none_8ma: pcfg-pull-none-8ma {
bias-disable;
drive-strength = <8>;
};
backlight-enable {
bl_en: bl-en {
rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
cros-ec {
ec_ap_int_l: ec-ap-int-l {
rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
discrete-regulators {
sd_io_pwr_en: sd-io-pwr-en {
rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO
&pcfg_pull_none>;
};
sd_pwr_1800_sel: sd-pwr-1800-sel {
rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO
&pcfg_pull_none>;
};
sd_slot_pwr_en: sd-slot-pwr-en {
rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO
&pcfg_pull_none>;
};
};
codec {
/* Has external pullup */
headset_int_l: headset-int-l {
rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>;
};
mic_int: mic-int {
rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
max98357a {
sdmode_en: sdmode-en {
rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
pcie {
pcie_clkreqn_cpm: pci-clkreqn-cpm {
/*
* Since our pcie doesn't support ClockPM(CPM), we want
* to hack this as gpio, so the EP could be able to
* de-assert it along and make ClockPM(CPM) work.
*/
rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
sdmmc {
/*
* We run sdmmc at max speed; bump up drive strength.
* We also have external pulls, so disable the internal ones.
*/
sdmmc_bus4: sdmmc-bus4 {
rockchip,pins =
<4 RK_PB0 1 &pcfg_pull_none_8ma>,
<4 RK_PB1 1 &pcfg_pull_none_8ma>,
<4 RK_PB2 1 &pcfg_pull_none_8ma>,
<4 RK_PB3 1 &pcfg_pull_none_8ma>;
};
sdmmc_clk: sdmmc-clk {
rockchip,pins =
<4 RK_PB4 1 &pcfg_pull_none_8ma>;
};
sdmmc_cmd: sdmmc-cmd {
rockchip,pins =
<4 RK_PB5 1 &pcfg_pull_none_8ma>;
};
/*
* In our case the official card detect is hooked to ground
* to avoid getting access to JTAG just by sticking something
* in the SD card slot (see the force_jtag bit in the TRM).
*
* We still configure it as card detect because it doesn't
* hurt and dw_mmc will ignore it. We make sure to disable
* the pull though so we don't burn needless power.
*/
sdmmc_cd: sdmmc-cd {
rockchip,pins =
<0 RK_PA7 1 &pcfg_pull_none>;
};
/* This is where we actually hook up CD; has external pull */
sdmmc_cd_gpio: sdmmc-cd-gpio {
rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
spi1 {
spi1_sleep: spi1-sleep {
/*
* Pull down SPI1 CLK/CS/RX/TX during suspend, to
* prevent leakage.
*/
rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>,
<1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>,
<1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>,
<1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>;
};
};
touchscreen {
touch_int_l: touch-int-l {
rockchip,pins = <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>;
};
touch_reset_l: touch-reset-l {
rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
trackpad {
ap_i2c_tp_pu_en: ap-i2c-tp-pu-en {
rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_output_high>;
};
trackpad_int_l: trackpad-int-l {
rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
wifi: wifi {
wlan_module_reset_l: wlan-module-reset-l {
rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>;
};
bt_host_wake_l: bt-host-wake-l {
/* Kevin has an external pull up, but Gru does not */
rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
write-protect {
ap_fw_wp: ap-fw-wp {
rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};